manualshive.com logo in svg

Geokon 4200ER, Инструкция по эксплуатации

Поделиться
Скачать
Geokon 4200ER Скачать руководство пользователя страница 14

8 

(Note that the display, although marked 

μ

E  is not directly in microstrains. The 

change in digits diplayed must be multiplied by the gage factor given on the 
calibration sheet to get the true microstrains) 

 
The GK-404 will continue to take measurements and display the readings until the OFF 
button is pushed, or if enabled, when the automatic Power-Off timer shuts the GK-404 off. 
 
The GK-404 continuously monitors the status of the (2) 1.5V AA cells, and when their 
combined voltage drops to 2V, the message 

Batteries Low 

is displayed on the screen. A 

fresh set of 1.5V AA batteries should be installed at this point 
 

3.3.  Operation of the GK-405 Readout Box 

 
The GK-405 Vibrating Wire Readout is made up of two components: 
 

  the Readout Unit, consisting of a Windows Mobile handheld PC running the GK-405 

Vibrating Wire Readout Application  

  the GK-405 Remote Module which is housed in a weather-proof enclosure and connects 

to the vibrating wire sensor by means of: 

 1) Flying leads with alligator type clips when the sensor cable terminates in bare wires or,  
 2) by means of a 10 pin connector.. 
 
The two components communicate wirelessly using Bluetooth

®

, a reliable digital 

communications protocol. The Readout Unit can operate from the cradle of the Remote 
Module (see Figure 5) or, if more convenient, can be removed and operated up to 20 meters 
from the Remote Module 
 

 

 

Figure 5  GK405 Readout Unit 

 
For further details consult the GK405 Instruction Manual.

 

 

Содержание 4200ER























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды