Genie GS-2669 DC Скачать руководство пользователя страница 111

Страница: 111 / 178

Service and Repair Manual

November 2016

Fault Codes

100

GS-2669 DC • GS-3369 DC • GS-4069 DC

Part No. 1272220GT

Faul t I ns pec tion Proc edur e

Fault Inspection Procedure

Check the device associated with the faulted circuit

Disconnect the faulted device connector.

Using a multi-meter, measure resistance between the two
terminals of the faulted device.

Resistance should be as follows.

Device

Typical Resistance

Solenoid Valve, Drive

27.2

Ω

Solenoid Valve, Steer

Ω

Solenoid Valve, Platform Up

Ω

Solenoid Valve, Platform Down

6.25

Ω

GCON and PCON Alarm

>1M

Ω

Automotive Horn

1.0

Ω

Contactor Coil

Ω

Go to step 2

No Good

Replace faulted device

Check the harness between the ground controls and the faulted device

Disconnect the GCON ECM connectors, C1, C2 and C3.
(or C4 if equipped with outriggers).

Disconnect the faulted device connector.

Check the continuity between the GCON ECM connector
and the signal side of the faulted device.



Result: Resistance should be close to 0

Ω.

Check the continuity between the return side of faulted
device and system ground.



Result: Resistance should be close to 0

Ω.

Check resistance between return side and signal side of
the harness plug of faulted device.



Result: Resistance should be 1M

Ω

or higher.

Go to step 3

No Good

Replace or repair harness

Check the GCON ECM

Содержание GS-2669 DC



















































































































































































Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды

Genie GS-2669 DC, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание GS-2669 DC

Отзывы:

Похожие инструкции для GS-2669 DC

Бренды по названию

Популярные бренды