General FCS18, Руководство оператора

Страница: 13 / 29

FCS18 RIP-R-STRIPPER FLOOR COVERING STRIPPER
FORM GOM19061901US, VERSION 1.0
English-EN
12
10 OPERATING INSTRUCTIONS
IMPORTANT:
DO NOT operate RIP-R-STRIPPER until each operator
completely comprehends contents of this manual.
RIP-R-
STRIPPER
SET-UP
ON JOBS
ITE
1. Position RIP-R-STRIPPER on a suitable work surface.
2.
Determine RIP-R-STRIPPER main power and blade ON/OFF switches
are in OFF position and machine is not connected to power source.
3. Determine operator handle is properly installed per procedures in
INSTALLING & ADJUSTING OPERATOR HANDLE in MACHINE SET-
UP section of this manual.
4. Install accessory blade per procedures in INSTALLING & REMOVING
ACCESSORY BLADES in MACHINE SET-UP section of this manual.
5. Connect factory supplied extension cord to machine by pushing in and
twisting to lock in place. FIGURE 18
FIGURE 18
6.
Connect additional extension cord to remaining end of factory supplied
extension cord (if applicable).
IMPORTANT: If additional extension cord is required, each cord must be of
proper structural integrity and size (AWG) to meet applicable National Electric
Code and OSHA requirements.
7. Connect extension cord or additional extension cord (if applicable) to
power source.
WARNING
•
All electrical wiring including extension cord gauge and/or
length must be installed and/or approved in accordance
with local electrical codes and practices.
•
An improper wiring installation can result in property
damage and/or personal injury.
WARNING
•
If operating RIP-R-STRIPPER in outside environment, use
only extension cords marked “W-A” or “W”.
•
Such cords are rated for outside usage and reduce risk of
electric shock.
DANGER
•
DO NOT operate RIP-R-STRIPPER without extension
cord, twist-lock connection device in proper operating
condition.
•
Always assume electrical wiring on every jobsite can
contain a fault.
•
A fault can generate a dangerous operating configuration
that can result in property damage and/or personal injury.
WARNING
•
DO NOT abuse the power cord. Never use power cord to
move RIP-R-STRIPPER or pull plug from receptacle.
Damage to cord and/or machine can result.
•
Keep cord away from heat, oil, sharp edges (including
accessory tool) or moving parts.
•
A damaged cord increases the risk of an electric shock.
CAUTION
•
If RIP-R-STRIPPER and/or an individual component/
accessory does not appear to function properly, STOP
and DO NOT operate RIP-R-STRIPPER until corrective
action has been completed.
•
Operation with improperly functioning machine,
components/accessories can result in property damage
and/or personal injury.
•
If you have any questions regarding proper operation of
RIP-R-STRIPPER, contact Customer Service Department
for assistance BEFORE using. There is no charge for this
service.
WARNING
•
Unexpected machine start-up can result in property
damage and/or personal injury.
WARNING
•
BEFORE use, inspect each extension cord and wiring
device for proper structural integrity.
•
DO NOT use cord with worn or cut outer jacket material or
repaired with electrical tape.
•
Use of cords with improper structural integrity can result
in property damage and/or personal injury.
WARNING
•
Floor covering removal process can produce excessive
noise, vibration and flying debris.
•
All operators and work personnel in RIP-R-STRIPPER
vicinity must wear appropriate safety eye wear and
hearing protection.
•
Other safety apparel and/or procedures, deemed
necessary by supervisory personnel, must also be worn
and/or practiced by all appropriate personnel.
CAUTION
•
Individual operator experience, skill, common sense, job site
location and specific job application will affect final decision on
specific operating procedures for RIP-R-STRIPPER.
•
Each operator must decide if he possesses adequate/proper
experience, skill and common sense for operating Hole Digger
in any given and/or specific job application.