manualshive.com logo in svg

General International 25-036, Руководство по установке и эксплуатации

Поделиться
Скачать
General International 25-036 Скачать руководство пользователя страница 12

9.

Align the inside edge of the stylus with the center 
point of the clamping bolt. The stylus is off center 
(eccentric) and it may be necessary to rotate the 
shaft to line it up,

J

.

10.

Move the carriage of the duplicator towards the tail-
stock and bring the point of the cutting tool against 
the point on the tailstock center as you did with the 
headstock.

If the 2 points are not lined up, your turning will be 
tapered. Simply loosen the mounting bolt on the sup-
port bracket where the 0 to 6 scale is located and 
move the duplicator in or out until the points touch.

11.

With the duplicator parallel to the lathe bed, firmly tighten the support beams using the supplied 19 mm 
wrench.

LEFT SIDE VIEW

RIGHT SIDE VIEW

J

DUPLICATING FROM A TURNING SAMPLE (ORIGINAL SPINDLE)

Now that the duplicator is mounted onto the machine and it is aligned parallel to the bed ways, you will need to
mount the part that you want to duplicate.

Note: Before you begin you must determine whether the turning has any sharp V cuts or angles. If so you will want
to use the fine point stylus attachment,

A

,

as the round stylus will not fit into tight grooves,

B

.

1.

Attach the fine point stylus by slipping the hole in the 
attachment over the round stylus, and tighten the 
lock knob,

C

.

If you were to mount the fine point attachment at the
current settings, your turning would be 1/2” larger than
your template. This happens because the attachment
point is 1/2” longer than the round stylus that you ali-
gned the center points with during the initial setup,

D

.

To correct this:

2.

Unplug the lathe from the power source.

3.

Set the retaining plate pin to the lowest setting on 
the ratchet plate 

E

.

4.

Turn the micro adjustment knob 

F

until the tip of the 

fine point attachment installed on the follower arm 
lines up with the center point of the clamping bolt.
(as shown in

D

).

5.

Turn thumb screws 

G

and 

H

to lock the setting. If the 

follower arm movement is not smooth, loosen the 
spring tension adjustment nut 

I

.

C

A

B

12

1/2”

D

H

I

F

G

E

Содержание 25-036





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды