background image

 

Use of 

WARNINGS,

CAUTIONS, etc.

 

Warnings, Cautions and other notes are included throughout this document to provide 
necessary information.  IGNORING WARNINGS, CAUTIONS AND OTHER NOTES 
MAY RESULT IN DAMAGE TO THE PRODUCT, INJURY, OR IN EXTREME CASES, 
DEATH.  You should know the use of Warnings, Cautions and other markings.  
Definitions are: 

 

WARNING! 

HIGHLIGHTS AN INSTALLATION, OPERATING OR MAINTENANCE 
PROCEDURE, PRACTICE, CONDITION, STATEMENT, ETC., WHICH, 
IF NOT STRICTLY OBSERVED, COULD RESULT IN INJURY TO OR 
DEATH OF PERSONNEL. 

 

CAUTION! 

HIGHLIGHTS AN INSTALLATION, OPERATING OR MAINTENANCE 
PROCEDURE, PRACTICE, CONDITION, STATEMENT, ETC., WHICH, 
IF NOT STRICTLY OBSERVED, COULD RESULT IN DAMAGE TO OR 
DESTRUCTION OF EQUIPMENT OR THE LOSS OF MISSION 
EFFECTIVENESS OR LONG TERM HEALTH HAZARDS TO 
PERSONNEL. 

 

Important: 

Highlights an essential installation, operating or maintenance 
procedure, practice, condition or statement, which, if heeded, will 
ensure efficiency and/or safety of said procedures. 

 

Note: 

Highlights an installation, operating or maintenance procedure, practice, 
condition or statement, which, if heeded, could enhance efficiency and/or 
safety of said procedures. 

 

ESD: 

The Electrostatic Sensitive Device (ESD) appears at the beginning of 
any procedure or procedural step that includes the handling of 
equipment sensitive to damage from electrostatic discharge. 

 

General Warnings and Cautions are also provided at the front of the document.  These 
Warnings and Cautions should be read by anyone who is involved with installation, has 
access to the equipment or is assigned to perform maintenance on the equipment. 

 

600-1152A ii 

 

Содержание SATCOM Technologies KX 120


























Отзывы: