Generac Power Systems PWRcell APKE00013 страница 37 Скачать руководство пользователя

Страница: 37 / 48

Commissioning and Setup

Installation Manual for Generac PWRCell Inverter

Navigate the inverter control panel until a screen

similar to

Figure 6-26

. When properly installed, the

inverter control panel will have an additional device

page called Ethernet Settings.

Figure 6-26. Ethernet Troubleshooting

NOTE:

Ensure blue Cat 5 cable is reconnected to the

Beacon after troubleshooting is complete.
If the PWRview State reads Get Connected then a suc

cessful connection has not been made to the PWRview

server.
If the inverter does not automatically connect to the

network and begin communicating with the PWRview

server, perform the following steps:

Verify an Ethernet connection has been enabled by

pressing the center button on the Ethernet page

and selecting Enable Ethernet.

Verify the network is configured for DHCP and that

DHCP is enabled.

If the network is not configured for DHCP, obtain

the MAC address and contact the system

administrator for IP address assignment.

Input IP address under Manual settings. See

Configuring Static IP Settings

Restart router and modem.

Contact system administrator for further

troubleshooting steps.

NOTE:

It is the installer’s responsibility to make sure the

Internet connection is reliable and secure. Generac

recommends always using a hardwired connection.

Generac does not recommend or support using any

wireless or power line carrier network devices. Use these

devices at your own discretion.

Commissioning Multiple Inverter

Systems

PLM Cross-talk

NOTE:

Do not energize two or more inverters before

commissioning. Energizing two or more inverters prior to

commissioning will result in cross-talk.

PWRcell inverters are manufactured with some common

default parameters. One of these default parameters is

the default Power Line Modem (PLM) channel. PWRcell

inverters use the PLM channel to communicate with and

send commands to REbus-powered devices. In this way,

a PWRcell inverter behaves like a master device. If two

or more master devices are communicating on the same

PLM channel, REbus devices become unable to respond

properly to the intended master device and the master

devices will attempt to provide control for the other, often

leading to communication and reporting issues. This is

referred to as cross-talk.

How to identify PLM Cross-talk

Cross-talk can be easily identified by navigating to the

device pages on an inverter control panel. If two inverter

device pages exist, or if devices connected to one

inverter show up on the other, cross-talk has occurred.

NOTE:

To differentiate one device page from another,

confirm the RCP numbers via the device page sub-menu.

NOTE:

It is recommended to keep a list of which REbus

devices are connected to specific inverters at multi-sys

tem sites.

Multiple Inverter System Pre-Commissioning

Checklist

Before commissioning multiple inverter systems, confirm

the following:

•

Inverter systems (including PV Links and PWRcell

batteries) have been installed per manufacturer

instructions and to local and state code require

ments.

•

PWRcell batteries have their Battery Disconnect

switches in the OFF position.

•

PWRcell inverters are de-energized with no volt

age present at their AC Grid input terminals. Use

an appropriately rated multi-meter/voltmeter to ver

ify if AC voltage is present at the AC Grid terminals.

NOTE:

To determine if the inverter is de-energized,

check the inverter control panel and the system backfeed

breaker. If de-energized, the inverter control panel will be

powered off and the inverter backfeed breaker will be

OPEN.

Multiple Inverter System Commissioning

Procedure

NOTE:

Throughout this process, it is important that only

one inverter is energized at any time. If two or more

inverters are energized at any point during this process,

the inverters will cross-talk. To resolve cross-talk, see

PLM Cross-talk Recovery Procedure

. After resolving

cross-talk, the commissioning process will need to be

restarted for the cross-talked inverters.

IP: 192.168.158.37

MAC:00:04:a3:0b:77:fc

DHCP: bound, 83285s
ARP: idle
DNS: done

ctr btn: net settings

009981

Содержание PWRcell APKE00013

















































Результаты поиска

Содержание PWRcell APKE00013

Отзывы:

Похожие инструкции для PWRcell APKE00013

Бренды по названию

Популярные бренды

Generac Power Systems PWRcell APKE00013, Руководство по установке

Результаты поиска

Содержание PWRcell APKE00013

Отзывы:

Похожие инструкции для PWRcell APKE00013

Бренды по названию

Популярные бренды