Generac Power Systems MLT6SMD, Руководство пользователя

Страница: 43 / 60

Maintenance
Owner’s Manual for MLT6SMD Light Tower 39
Section 4: Maintenance
Emissions Information
For emissions warranty information, please refer to the
diesel engine manual supplied with this unit.
Daily Walk-Around Inspection
Perform a walk-around inspection of the unit every day
before starting the unit. Look for conditions that could
hinder performance or safety, such as (but not limited to):
•
Oil/coolant/fuel leakage
•
Blocked vents
•
Loose/missing hardware
•
Loose or broken electrical connections
Inspect the fan belt for cracks, fraying, or stretching. Verify
the belt is properly seated in the pulley grooves. Replace
the belt according to the manufacturer’s recommendations.
General Maintenance
Incorrectly maintained equipment can become a safety
hazard. In order for equipment to operate safely and
correctly over a long period of time, periodic maintenance
and occasional repairs are necessary.
DO NOT perform
routine service (oil and filter changes, cleaning, etc.)
unless all electrical components are shut off.
Regular maintenance will improve performance and
extend engine/equipment life. Generac Mobile Products,
LLC recommends that all maintenance work be per-
formed by a GMP ASD. Regular maintenance, replace-
ment, or repair of the emissions control devices and
systems may be performed by any repair shop or person
of the owner’s choosing. However, to obtain emissions
control warranty service free of charge, the work must be
performed by a GMP ASD or authorized Mitsubishi
®
engine dealer depending on the repair. See the emis-
sions warranty.
Preparing for Service
Before servicing the unit, always follow the instructions
listed below.
1. Verify the control power switch is OFF.
2. Verify the circuit breakers are OFF.
3. Disconnect the negative (–) terminal on the battery.
4. Attach a “Do Not Start” sign to the control panel to
signify that the unit is being serviced and reduce
the chance of unwanted operation.
Cleaning the Unit
Always clean the unit after each use to remove dust,
grease, mud, or spilled fuel or oil. Use soft, clean rags to
wipe the cabinet exterior and control panel. Low-pressure
compressed air (less than 40 psi [276 kPa]) can also be
used to remove dust and debris from the cabinet interior.
This unit contains sensitive electronic components that
can be damaged by high pressure and heat.
Do not :
•
wash the unit with a high pressure hose or power
washer.
•
wash the engine block or fuel tank with a power
washer or steam cleaner. Water may enter the
cabinet and collect in the generator windings or
other electrical parts, causing damage.
Inspecting the Unit
•
If the unit is stored outside, inspect for water inside
the cabinet and generator before each use. If wet,
dry the unit thoroughly before starting.
•
Inspect condition of electrical cords. DO NOT use
the unit if insulation is cut or worn through.
•
Verify winch cables are in good condition and
centered on each pulley.
DO NOT use a cable that
is kinked or starting to unravel.
•
Verify the safety pins for the mast lock rod and
mast lock bar are present and secured with a
chain. Verify that the spring located in the mast
lock bar is not broken or missing. Verify the
operation of the mast lock bar.
•
Verify the wheel lugs are present and properly
tightened. Refer to
Towing Safety .
•
Inspect the coolant level in the coolant overflow jug
located near the radiator. Refer to the engine
operator’s manual for coolant recommendations
and proper mixture. Normal operating level is
between the ‘full’ and ‘add’ markings on the
overflow jug.
•
After engine is stopped and completely cool, cool-
ant may be added directly to the coolant overflow
jug.
CAUTION
(000306)
Equipment Damage. Failure to perform a daily
inspection could result in damage to the unit.
CAUTION
(000325a)
Equipment damage. Never spray water to clean unit.
Do not introduce water into generator widings,
terminals, or fuel system during the cleaning process.
Doing so will result in equipment damage.