Generac Power Systems MLT6SMD Скачать руководство пользователя страница 48

Страница: 48 / 60

Troubleshooting

Owner’s Manual for MLT6SMD Light Tower

If problems continue, contact Generac Mobile Products, LLC at 1-800-926-9768 for assistance.

Problem

Possible Cause

Solution

Unit cranks, but will not start

Low fuel level.

Verify fuel level in tank.

Fuel flow obstructed.

Check fuel pump operation.

Inspect fuel supply hose from tank to fuel filter for
cracks and abrasion.

Inspect for gelled fuel in fuel system in cold
weather, especially at fuel filter.

Air in fuel system.

Purge air from fuel system.

Restricted air filter.

Inspect air filter for blockage.

Glow plug(s) inoperable.

Refer to OEM engine operator’s manual for
additional information.

Unit starts, but stumbles and dies

Low ambient temperature.

Verify if ambient temperature is within unit limits.

Intake heater inoperable.

Inspect engine air inlet heater functionality.

Air in fuel lines.

Purge air from fuel lines.

High coolant temperature shutdown

Low coolant level.

Allow engine to cool, then check coolant level in
radiator. Add coolant if needed.

Blockage in radiator.

Inspect radiator surroundings for blockage and
remove any foreign matter.

Debris on radiator face.

Broken coolant pump belt.

Inspect for visible leaks. Check tension of water
pump drive belt.

Cooling fan inoperable.

Remove load on generator and restart engine.

Check coolant temperature and shut engine down
immediately if it starts to overheat.

Low oil pressure shutdown

Low oil level.

Check oil level. Add oil if necessary.

Oil pump inoperable.

Contact a GMP ASD.

Unit stalls when export power is used

Load exceeds unit rating.

Turn outlet breaker ON and load sense switch
OFF, confirm generator output is 60 Hz ± 2 Hz.
Reapply load.

One or more lights do not turn on

Light breaker tripped.

Inspect light breakers.

Lights not turned on.

Inspect electronic control to see if lights are on.
Turn lights on.

The lights are flashing

Dusk-to-dawn sensor
adjustment needed.

Adjust the dusk-to-dawn sensor according to

Dusk to Dawn Sensor

Low generator frequency.

Verify AC frequency is >40hz.

Содержание MLT6SMD





























































Результаты поиска

Содержание MLT6SMD

Отзывы:

Похожие инструкции для MLT6SMD

Бренды по названию

Популярные бренды

Generac Power Systems MLT6SMD, Руководство пользователя

Результаты поиска

Содержание MLT6SMD

Отзывы:

Похожие инструкции для MLT6SMD

Бренды по названию

Популярные бренды