manualshive.com logo in svg

Generac Power Systems MLT4200IF4, Руководство пользователя, Страница: 40 / 59

Поделиться
Скачать
Generac Power Systems MLT4200IF4 Скачать руководство пользователя страница 40

Maintenance

34

Owner’s Manual for MLT4200IF4 Light Tower

•

Verify the wheel lugs are present and properly
tightened. Refer to

 

Towing Safety

.

•

Check the coolant level daily by inspecting the
level in coolant overflow jug located near the
radiator. Refer to the engine operator’s manual for
coolant recommendations and proper mixture.
Normal operating level is between the ‘full’ and
‘add’ markings on the overflow jug.

•

AFTER ENGINE IS STOPPED AND COMPLETELY
COOL

, coolant may be added directly to the coolant

overflow jug.

•

Check the oil level daily. Refer to the engine
operator’s manual for the appropriate oil specification.
Make sure that the oil is correct for special operating
conditions such as a change in season or climate.

•

DO NOT

 start the unit if the engine oil level is

below the ADD mark on the dipstick.

• Normal operating level is in the cross-hatch

pattern between the full and add markings on
the dipstick.

• Add oil only if the oil level is below the add mark

on the bottom of the cross-hatch pattern on the
dipstick. 

DO NOT OVERFILL

 the crankcase.

•

Check the fuel level.

•

If the unit is connected to a remote start or transfer
switch, verify the remote switch is also off and
tagged.

NOTE: 

If the engine was run out of fuel or the fuel tank

was drained, it may be necessary to bleed the fuel lines.
Refer to the engine operator’s manual supplied with the
unit.

Basic Maintenance Schedule

Refer to the original equipment manufacturer’s operating
manual for a complete list of maintenance requirements.
Failure to comply with the procedures as described in the
engine operator’s manual will nullify the warranty,
decrease performance and cause equipment damage or
premature equipment failure. Maintenance records may
be required to complete a warranty request.

Use the schedule in the following table as a guide for
regular maintenance intervals. For additional or
replacement copies of the engine operator’s manual,
contact a Generac Mobile Products Authorized Service
Dealer.

Table 4-1. Basic Maintenance Guide

Item

Daily

250 

Hours

500

Hours

1000 

Hours

Check Oil Level

Check Coolant Level

Check Fuel Level

Drain Fuel Filter

Check Tire Pressure

Inspect Wheel Bearings

Check All Electrical Connections

Clean Battery

Check Fan Belt Tension (replace if necessary)

Inspect Radiator Fins For Debris; Clean As Required

Preheating Condition Check

Check Engine Starting Conditions and Noise Conditions

Check Exhaust Smoke Condition

Inspect Light Tower Winch For Proper Operation

Replace Engine Oil

Replace Fuel Filter Element

Clean Water Sedimenter Element

Electromagnetic Pump Filter Replacement or Cleaning

Check Fan Belt Tension (replace if necessary)

Oil Filter Element Replacement

Replace Air Filter Element

Lubricate Leveling Jacks

Replace Heated Fuel Filter (if equipped)

Inspect Engine Starting Battery

To order go to Discount-Equipment.com

Содержание MLT4200IF4




























































Отзывы:

Нет отзывов