manualshive.com logo in svg

Generac Power Systems MAGNUM MLT6SKDS, Руководство пользователя

Поделиться
Скачать
Generac Power Systems MAGNUM MLT6SKDS Скачать руководство пользователя страница 39

Operation

Owner’s Manual for MLT6SMDS - MLT6SKDS Light Tower

35

is closed by verifying that the knob has rotated perpen-
dicular to the pipe centerline. If valve does not close, con-
tact Generac Mobile Products Technical Support.

Reset the PAS

IMPORTANT  NOTE:  Before  resetting  the  PAS,  turn
the  control  power  switch  OFF  (O).  This  will  prevent
unexpected engine start-up during the procedure.

1.

Rotate  the  reset  knob  and  hold  it  in  place  while
pulling the T-handle until reset knob rotates coun-
terclockwise into plunger detent. An audible “click”
indicates the reset knob has seated properly.

2.

Verify  that  the  reset  knob  is  parallel  to  the  intake
pipe centerline. 

3.

Release  T-handle,  and  then  release  reset  knob.
The reset knob should remain parallel to the intake
pipe centerline.

Lower Radiator Hose Heater 

(If Equipped)

The  lower  radiator  hose  heater  is  designed  to  prevent
engine  coolant  from  freezing  in  extreme  cold  weather
conditions. While the heater is designed to be operated
overnight if necessary, 2–5 hours of heating just prior to
starting is usually sufficient for proper engine starting.

NOTE: 

Use  the  lower  radiator  hose  heater  only  in  its

designated  location.  Incorrect  use  can  damage  the
engine.

Proceed as follows when operating a unit equipped with
a lower radiator hose heater.

1.

Verify  the  unit  is  level  to  maintain  correct  orienta-
tion of the heater while it is in operation.

2.

Verify  the  cooling  system  is  full  of  the  correct
mixture  of  water  and  engine  coolant  before  each
heater use.

3.

Use  only  an  undamaged,  outdoor  rated,  three-
prong  grounded  120VAC  extension  cord  with  a
minimum  amperage  rating  of  10A.  Connect  the
cord to a properly grounded 120VAC GFCI outlet.

4.

Before  starting  the  engine,  unplug  the  extension
cord  from  the  power  first,  then  unplug  the  heater
cord set from the extension cord.

Tandem Tow (If Equipped)

See 

Figure 3-19

. The tandem tow hitch option (A) allows

the operator to tow a second MLT6 Light Tower in series
behind the unit equipped with the hitch.

IMPORTANT  NOTE:  Never tow more than two units
at once.

•

Connect  any  trailer  wiring  to  the  unit  in  front  (B).
Inspect for proper operation of the directional and
brake lights.

•

Connect the towing chains to the tie down locations
(C).

•

Avoid sharp turns when towing. 

Do not

 cross any

obstacles more than 12 in (30.5 cm) deep.

•

Tandem tow speeds:
a. Paved highway—45 mph (72 km/h)
b. Graded gravel—25 mph (40 km/h)
c. Cross country—10 mph (16 km/h)

 

Figure 3-19. Tandem Tow

Telemetry (If Equipped)

The  digital  telemetry  option  enables  the  operator  to
remotely  monitor  the  unit  fuel  level. A  transmitter  inside
the  engine  compartment  sends  real  time  equipment
status  information  to  the  user  via  cellular  or  satellite
connection.

Spark Arrester (If Equipped)

A  spark  arrester,  installed  on  the  unit  exhaust,  may  be
required  by  code  in  certain  municipalities.  Contact  the
local authority having jurisdiction to determine if a spark
arrester must be installed on the unit before operation. 

Heated Fuel Filter (If Equipped)

See 

Figure 3-20

. An  optional  heated  fuel  filter  (A)  pre-

vents diesel fuel from gelling in extremely cold tempera-
tures. Heating cycles are automatically controlled by the
Power Zone–DLA. 

Figure 3-20. Heated Fuel Filter

004770

A

B

C

C

A

Содержание MAGNUM MLT6SKDS





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды