Generac Power Systems MAGNUM MLT4250 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 49

background image

Operation

Owner’s Manual for MLT Light Tower

21

Prestart Checklist

Before starting the unit, all items in the prestart check-
list must be completed. This checklist applies to both
manual and remote starting of the unit.



Verify all maintenance procedures are up to date. For
more information, refer to

General Maintenance

and

Basic Maintenance Schedule



The unit must be level.



The unit must be dry. Look for water inside or near
the unit; dry if needed.



For grounding requirements, follow any local, state,
or National Electrical Code (NEC) guidelines.



Verify the Control Power switch is in the OFF (O)
position.



Verify all circuit breakers are in the OFF (O) position.



Inspect all electrical cords; repair or replace any that
are cut, worn, or bare.



Verify all winch cables are in good condition and
centered on each pulley. Do not use if cables are
kinked or beginning to unravel.



Check oil, coolant, and fuel levels. For more
information, refer to

General Maintenance



Verify battery connections are secure.



Turn the battery disconnect switch on, if equipped.



Check the engine fan belt tension and condition.



Check the engine fan belt guard.



Check the engine exhaust system for loose or rusted
components.



Verify all covers are in place and secure.



Verify all electrical connections at the connection
lugs, if equipped, are tight and wired correctly.



Verify the voltage selector switch is set to the desired
voltage and locked.



Verify the emergency stop switch is pulled out.

Starting the Unit—Manually

1. Move the Control Power switch to the ON (I)

position.

2. See

Figure 3-12

. The LCD window will quickly

display system information, all LEDs will flash.

Figure 3-12. Starting the Machine

3. See

Figure 3-13

. the Ready screen will be

displayed and the LCD window will indicate Manual
mode. The Ready/Manual LED will be lit.

NOTE:

The unit must be in the Manual mode with the

Ready/Manual LED lit to start the unit.

Figure 3-13. Manual Mode

4. See

Figure 3-14

. Press ENGINE START. The

Prestart screen will be displayed (if equipped) and
a countdown will begin from 20 seconds to 0.

(000100a)

WARNING

Consult Manual. Read and understand manual
completely before using product. Failure to
completely understand manual and product
could result in death or serious injury.

004530

004531

Discount-Equipment.com

«
...
23
24
25
26
27
...
»

Содержание MAGNUM MLT4250


















































Отзывы:

Нет отзывов

Похожие инструкции для MAGNUM MLT4250

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Jacobs Ladder Страницы: 16

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: Kamar Страницы: 2

INTRAmatic 31 ES

Бренд: KaVo Страницы: 52

Бренд: Erbe Страницы: 124

SAS-1 Immunofix

Бренд: helena BioSciences Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды