Generac Power Systems G10 Скачать руководство пользователя страница 23

 

2-Year Limited Warranty 

 

Terms and Conditions 

The GENERAC

 KINETIC LOG SPLITTER is warranted for two (2) years against defects in materials or workmanship 

when put to ordinary and normal consumer use; ninety (90) days for any other use. 

For the purposes of all the above warranties, “ordinary and normal consumer use” refers to non-commercial residential 
use and does not include misuse, accidents or damage due to inadequate maintenance. 

Generac Power Systems certifies that the GENERAC

 KINETIC LOG SPLITTER is fit for ordinary purposes for which a 

product of this type is used. Generac Power Systems however, limits the implied warranties of merchantability and 
fitness in duration to a period of two (2) years in consumer use, ninety (90) days for any other use.

 

The 2-Year Limited Warranty on the GENERAC

 KINETIC LOG SPLITTER starts on the date the machine ships from our 

factory. The 2-Year Limited Warranty is applicable only to the original owner. 

The warranty holder is responsible for the performance of the required maintenance as defined by the manufacturer's 
owner's manuals. The warranty holder is responsible for replacement of normally wearing parts such as the Drive Belt. 
Accessories to the machine are not covered by this warranty. 

During the warranty period, the warranty holder is responsible for the machine transportation charges, if required. 
During the warranty period, warranty parts will be shipped by standard method at no charge to the warranty holder. 
Expedited shipping of warranty parts is the responsibility of the warranty holder. 

SOME STATES DO NOT ALLOW LIMITATIONS ON THE LENGTH OF IMPLIED WARRANTIES, SO THE ABOVE 
LIMITATIONS MAY NOT APPLY TO YOU.

 

Generac Power Systems shall not be liable under any circumstances for any incidental or consequential damages or 
expenses of any kind, including, but not limited to, cost of equipment rentals, loss of profit, or cost of hiring services to 
perform tasks normally performed by the GENERAC

 KINETIC LOG SPLITTER. 

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL 
DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU ALSO HAVE OTHER RIGHTS, WHICH VARY 
FROM STATE TO STATE.

 

 

GENERAC

®

 

KINETIC LOG SPLITTER

 

 

Содержание G10

























Отзывы: