Generac Power Systems 004626-1 Скачать руководство пользователя страница 2

Generac

®

Power Systems, Inc.

INTRODUCTION

Thank you for purchasing the Guardian product line
by Generac Power Systems. This model is a compact,
high performance, liquid-cooled, engine-driven gen-
erator designed to automatically supply electrical
power to operate critical loads during a utility power
failure.

This unit is factory installed in an all-weather, metal
enclosure that is intended exclusively for outdoor
installation.

READ THIS MANUAL THOROUGHLY

If you do not understand any portion of this manual,
contact Generac or the nearest Generac/Guardian
Authorized Dealer for starting, operating and servicing
procedures.

Throughout this publication, and on tags and 
decals affixed to the generator, DANGER, WARNING,
CAUTION and NOTE blocks are used to alert you to
special instruction about a particular operation that
may be hazardous if performed incorrectly or care-
lessly. Observe them carefully. Their definitions are as
follows:

After this heading, read instructions that, if not
strictly complied with, will result in personal injury
or property damage.

After this heading, read instructions that, if not
strictly complied with, may result in personal injury
or property damage.

After this heading, read instructions that, if not
strictly complied with, could result in damage to
equipment and/or property.

NOTE:

After this heading, read explanatory state-
ments that require special emphasis.

These safety warnings cannot eliminate the hazards
that they indicate. Common sense and strict compli-
ance with the special instructions while performing
the service are essential to preventing accidents.

Four commonly used safety symbols accompany the
DANGER, WARNING and CAUTION blocks. The type
of information each indicates is as follows:

This symbol points out important safety informa-
tion that, if not followed, could endanger personal
safety and/or property.

This symbol points out potential explosion hazard.

This symbol points out potential fire hazard.

This symbol points out potential electrical shock
hazard.

The operator is responsible for proper and safe use
of the equipment. Generac strongly recommends that
the operator read this 

Owner's Manual

and thor-

oughly understand all instructions before using this
equipment. Generac also strongly recommends
instructing other users to properly start and operate
the unit. This prepares them if they need to operate
the equipment in an emergency.

CONTENTS

This manual contains pertinent owner’s information,
including warranty, electrical diagrams, exploded
views and lists of repair parts, for Guardian models:

004373-1 & 004626-0.

OPERATION AND MAINTENANCE

It is the operator's responsibility to perform all safety
checks, to make sure that all maintenance for safe
operation is performed promptly, and to have the
equipment checked periodically by a Generac/
Guardian Authorized Dealer. Normal maintenance
service and replacement of maintenance parts are the
responsibility of the owner/operator and, as such, are
not considered defects in materials or workmanship
within the terms of the warranty. Individual operating
habits and usage contribute to the need for mainte-
nance service.

Proper maintenance and care of the generator ensure a
minimum number of problems and keep operating
expenses at a minimum. See a Generac/Guardian
Authorized Dealer for service aids and accessories.

HOW TO OBTAIN SERVICE

When the generator requires servicing or repairs,
simply contact a Generac/Guardian Authorized
Dealer for assistance. Service technicians are factory-
trained and are capable of handling all service needs.

When contacting a Generac/Guardian Authorized
Dealer or the factory about parts and service, always
supply the complete model number and serial num-
ber of the unit as given on its data decal, which is
located on the generator.

Model No. ____________ Serial No. ______________

!

DANGER

AUTHORIZED

DEALER LOCATION

To locate the GENERAC/GUARDIAN AUTHORIZED 

DEALER nearest you, please call this number:

1-800-333-1322

DEALER LOCATION INFORMATION 

CAN BE OBTAINED AT THIS NUMBER.

Содержание 004626-1





























































Отзывы: