Generac Mobile MDE570P Скачать руководство пользователя страница 48

Страница: 48 / 80

Owner’s Manual for Mobile Generator

finished oils.
To achieve the best performance from a Perkins engine,

conform to the following guidelines:

•

See

Figure 4-1

to find the correct oil viscosity

grade for your engine.

•

At the specified interval, service the engine. Use

new oil and install a new oil filter.

•

Perform maintenance at the intervals that are

specified in

Basic Maintenance Schedule

Oil analysis

See

Figure 4-2

. This engine is equipped with an oil

sampling valve (A).

Figure 4-2. Oil Sampling Valve

If oil analysis is required, the oil sampling valve is used to

obtain samples of the engine oil. The oil analysis will

complement the preventive maintenance program.
The oil analysis is a diagnostic tool that is used to

determine oil performance and component wear rates.

Contamination can be identified and measured by using

oil analysis. The oil analysis includes the following tests:

•

The Wear Rate Analysis monitors the wear of the

engines metals. The amount of wear metal and

type of wear metal that is in the oil is analyzed. The

increase in the rate of engine wear metal in the oil

is as important as the quantity of engine wear

metal in the oil.

•

Tests are conducted to detect contamination of the

oil by water, glycol, or fuel.

•

The Oil Condition Analysis determines the loss of

the oils lubricating properties. An infrared analysis

is used to compare the properties of new oil to the

properties of the used oil sample. This analysis

allows technicians to determine the amount of

deterioration of the oil during use. This analysis

also allows technicians to verify the performance of

the oil according to the specification during the

entire oil change interval.

Coolant Recommendation

Acceptable Coolant Types

Coolant Mixtures and Freezing Points

NOTE:

For more information, see OEM engine manual.

Coolant Type

Service Life*

Perkins ELC

6,000 service hours or

3 years

Commercial heavy-duty anti-freeze

that meets ASTM D6210

3,000 service hours or

2 years

Commercial SCA inhibitor and

water

3,000 service hours or

1 year

*Use the interval that occurs first. The cooling system must

also be flushed at this time.

Freezing Point °F (°C)

-12

(-24)

-34

(-36)

-54

(-48)

-90

(-67)

Water (% Volume)

Anitfreeze (% Volume)

60*

* Maximum freeze protection is 60%.

(000149)

DANGER

Risk of poisoning. Do not use mouth to siphon
coolant. Doing so will result in death or serious
injury.

(000154)

WARNING

Risk of burns. Do not open coolant system
until engine has completely cooled. Doing so
could result in serious injury.

Risk of overheating. Do not use any chromate base
rust inhibitor with propylene glycol base antifreeze,
boosters, or additives. Doing so will cause overheating
and possible equipment damage.

(000165a)

CAUTION

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 48 / 80

Результаты поиска

Содержание MDE570P

Отзывы: