Generac Mobile MDE570P Скачать руководство пользователя страница 40

Страница: 40 / 80

Owner’s Manual for Mobile Generator

IMPORTANT NOTE: This must be performed by a

certified electrician.

Before attempting any connections, verify the main circuit

breaker and the control power switch are in the OFF (O)

position and that the negative (-) battery cable has been

disconnected from the battery.
Installation of such devices must be performed by

following all directions supplied by the manufacturer of

the switch. If attaching the unit to a power supply

normally serviced by a utility company, notify the utility

company and check state and local regulations.

Familiarize yourself with all instructions and warning

labels supplied with the switch.
When the unit is used as a standby power supply, it must

be equipped with a transfer switch that isolates it from the

utility’s distribution system. A transfer switch is designed

to transfer electrical loads from the normal power source

(utility) to the emergency power source (generator) when

normal voltage falls below a prescribed level. The

transfer switch automatically returns the load back to the

normal source when power is restored back to operating

levels.

Figure 3-15. Transfer Switch Operation

Changing Exercise Timers

If exercise timers or scheduled runs are needed, contact

a GMASD for assistance.

Shutting Down the Unit

Before shutting down the unit, check with personnel

using power supplied by the generator and let them know

the power is being switched off. Verify the power

shutdown will not create any hazards by accidentally

turning off equipment that must continue operating (such

as pumps, compressors, lights).

Remove all loads from the generator by opening all

circuit breakers (turn to the OFF (O) position).

Allow engine to run for approximately five minutes

to allow it to cool down.

Press the red engine STOP/RESET (O) button on

the controller.

After pressing the red engine STOP/RESET (O)

button, the unit may continue to run for an addi

tional cool down period. This is being driven by the

engine controller to ensure engine temperatures

have cooled sufficiently.

After the unit shuts down, wait for the battery dis

connect LED to turn off. When the LED shuts off.

Then, it is safe to switch the disconnect connect

switch to off.

NOTE:

The ECU must run for 90 seconds after

shutdown to purge the DEF.

NOTE:

Switching off the control panel before the

controller finishes updating could cause a loss of data.

NOTE:

For extended storage time, disconnect the

battery. See the OEM engine manual for extended

storage requirements.

NOTE:

If any units are in parallel, do not disconnect the

MSC cable.

Emergency Stop Switch

See

Figure 3-16

. The unit is equipped with one

emergency stop switch. The red button is clearly labeled

EMERGENCY STOP. The switch can be accessed and

activated with all doors closed and locked.

Incoming utility power

Emergency distribution panel (generator power)

Main distribution panel (utility power)

Transfer switch

Power from generator

Utility meter

WHITE

Incoming utility power

GRAY

Normal utility power circuit

BLACK

Emergency generator power circuit

002807

CAUTION

(000246b)

Equipment Damage. The emergency stop switch is
not to be used to power down the unit under normal
operating circumstances. Doing so could result in
equipment damage.

Содержание MDE570P

















































































Результаты поиска

Содержание MDE570P

Отзывы:

Generac Mobile MDE570P, Руководство пользователя, Страница: 40 / 80

Результаты поиска

Содержание MDE570P

Отзывы: