background image

11 
 

 

Figure 9. Controlling the zone with Smart IP Manager software. 

Editing acoustic settings 

The frequency response of the 4420A can be compensated for the room’s 
acoustical influences by editing the settings in the Acoustics tab in the Genelec 
Smart IP Manager. Acoustical calibration settings are specific to each 
loudspeaker.  

To set, select one or more loudspeakers in the device list. Selecting more than 
one loudspeaker applies the settings to all selected loudspeakers at once.  

To adjust, select the Acoustics tab. You have several controls in the tab 

  delay (delay alignment control) 

  sensitivity (to align this loudspeaker output level with other loudspeakers) 

  20 parametric acoustic settings (to compensate to room acoustic 

influences) 

The acoustic measuring tool normally used by AV installers can be used to set 
these adjustments. Careful listening with test recordings is also recommended.  

For each parametric filter, select the filter by clicking on the filter box icon. Select 
the function for this filter in the Type drop down box. Each parametric filter has 
up to three slider controls that set the parameter values. Quick selections are 
also provided for Bass Roll-off, Bass Tilt and Treble Tilt.  

Turn on audio inputs:  

mix 

à

 stream in 

à

 

analogue in 

à

 no input 

à

 

mix.  

Unallocated Smart IP 
devices are listed under 
“Default” zone.  

Zone can be muted and 
level controlled with ‘-’  
and ‘+’ buttons.  

Содержание 4420A





















Отзывы: