Gemalto Cinterion PLS62T-W USB Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 91

Gemalto Cinterion PLS62T-W USB Скачать руководство пользователя страница 56

Cinterion

®

Java Terminal Hardware Interface Description

5.2 Mounting the Java Terminal

57



PLS62T-W_HID_v01

2018-06-20

Confidential / Prelimenary

Page 56 of 91

5.2

Mounting the Java Terminal

There are a number of ways to mount the Java Terminal:

•

Java Terminal can be attached to a rail installation or other surface using the two provided
screw holes for screws, e.g., size M3.

•

Java Terminal can be fastened to a rack or holding using the two provided fixtures for cable
straps.

•

Java Terminal can be slid onto a specific DIN rail made according to DIN EN 60715 - C sec-
tion, C30 format. A catch at the terminal’s bottom side will have to be removed to slide mul-
tiple terminals onto a single rail.

•

Using a BOPLA TSH 35-2 universal DIN rail holder the Java Terminal can be fitted onto
another special type of DIN rail made according to DIN EN 60715 - Top hat section, 35mm
(e.g., Wago 210-113 steel carrier rail).

The following figure shows the various possibilities provided to mount the Java Terminal.

Figure 16:

Mounting the Java Terminal

The various ways to mount the Java Terminal may be combined where appropriate. It is for ex-
ample possible to slide the terminal onto a DIN rail and in addition use cable straps to fasten it
to a holding.

Catch to mount

Screw holes for

Screw holes

Fixtures for

cable straps

DIN rail holder

C-rail (C30)

BOPLA TSH 35-2

«
...
54
55
56
57
58
...
»

Содержание Cinterion PLS62T-W USB




























































































Отзывы:

Нет отзывов