GEM 639 eSyStep Скачать руководство пользователя страница 29

Страница: 29 / 67

www.gemu-group.com

29 / 67

GEMÜ 639 eSyStep

OPEN / CLOSE (Code AE)

10.3 Installation with clamp connections

Fig. 1: Clamp connection

NOTICE

Gasket and clamp

▶

The gasket and clamps for clamp connections are not in-

cluded in the scope of delivery.

1. Keep ready gasket and clamp.
2. Carry out preparation for installation (see chapter "Prepar-

ing for installation").

3. Insert the corresponding gasket between the body of the

product and the pipe connection.

4. Connect the gasket between the body of the product and

the pipe connection using clamps.

5. Re-attach or reactivate all safety and protective devices.

10.4 Installation with butt weld spigots

Fig. 2: Butt weld spigots

1. Carry out preparations for installation (see chapter "Pre-

paring for installation").

2. Adhere to good welding practices!
3. Remove actuator

(see chapter "Removing the actuator").

4. Weld the body of the product in the piping.
5. Allow butt weld spigots to cool down.
6. Mount actuator

(see chapter "Mounting the actuator").

7. Re-attach or reactivate all safety and protective devices.
8. Flush the system.

10.5 Installation with threaded sockets

Fig. 3: Threaded socket

NOTICE

Sealing material

▶

The sealing material is not included in the scope of deliv-

ery.

●

Only use appropriate sealing material.

1. Keep thread sealant ready.
2. Carry out preparations for installation (see chapter "Pre-

paring for installation").

3. Screw the threaded connections into the pipe in accord-

ance with valid standards.

4. Screw the body of the product onto the piping using ap-

propriate thread sealant.

5. Re-attach or reactivate all safety and protective devices.

10.6 Installation with threaded spigots

Fig. 4: Threaded spigots

NOTICE

Thread sealant

▶

The thread sealant is not included in the scope of deliv-

ery.

●

Only use appropriate thread sealant.

1. Keep thread sealant ready.
2. Carry out preparations for installation (see chapter "Pre-

paring for installation").

3. Screw the pipe into the threaded connection of the valve

body in accordance with valid standards.

Use appropriate thread sealant.

4. Re-attach or reactivate all safety and protective devices.

10 Installation in piping

Содержание 639 eSyStep




































































Результаты поиска

Содержание 639 eSyStep

Отзывы:

Похожие инструкции для 639 eSyStep

Бренды по названию

Популярные бренды

GEM 639 eSyStep, Руководство по эксплуатации

Результаты поиска

Содержание 639 eSyStep

Отзывы:

Похожие инструкции для 639 eSyStep

Бренды по названию

Популярные бренды