manualshive.com logo in svg

GEITH QC100 H1, Руководство пользователя

Поделиться
Скачать
GEITH QC100 H1 Скачать руководство пользователя страница 24

3-4

www.geith.com

OPERATION

Four Port Control Box

Figure 8

Press the POWER button (1) 

[Figure 8]

. An alarm will

sound and button will illuminate.

Press unlock button (2) 

[Figure 8]

 within six seconds of

pressing power button. Alarm will change tone and
unlock button will illuminate.

NOTE: Unlock button (2) [Figure 8] must be pressed

within six seconds of pressing power button
or  system  will  not  operate  (alarm  and  lights
will  shut-off).  If  this  occurs,  restart  the
procedure by pressing the power button. 

Figure 9

Crowd quick coupler to build pressure until sliding hook
(3) and locking clasp (4) 

[Figure 9]

 open.

NOTE: After operating pressure has been achieved in

the quick coupler system, all four buttons on
the control  box will  illuminate  and  the alarm
tone will become constant. 

Figure 10

With the quick coupler crowded fully inwards, press the
system LOCK button (1) 

[Figure 10]

.

NOTE: When LOCK button (1) [Figure 10] is pressed,

all lights and alarm will shut off.

Figure 11

Continue to crowd coupler for 10 seconds until the
locking clasp (2) fully closes and the sliding hook (3)

[Figure 11]

 fully lowers.

Stop the engine and exit the machine. 

Check the hydraulic lines, connections, fittings and
cylinder for hydraulic oil leaks. Repair or replace
damaged parts as necessary.

NOTE: If  the  quick  coupler  does  not  operate  as

described, check that the hydraulic hoses are
connected  properly  (See  Four  Port  Control
Box  on  Page  5-1).  If  further  assistance  in
needed,  see  your  GEITH  distributor  for
service.

2

1

3

4

1

3

2

Содержание QC100 H1



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды