GEITH QC100 H1 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 58

background image

www.geith.com

2-3

SAFETY

Operation

Attachment

Never let anyone ride on any work attachment. This
creates a falling and crushing hazard, and can result in
death or serious injury.

Move work levers (joysticks) in a continuous motion.
Making sudden movements with the work levers
(joysticks) can cause attachment to swing into cabin or
into a person in work area. This can result in death or
serious injury.

Do not use work equipment or swing mechanism to pull
load in any direction. This could cause the work
equipment to move suddenly if the load releases and can
result in death or serious injury.

Maintenance and Installation

Improper operation and maintenance can result in death
or serious injury. Read manual before operating or
maintaining the attachment. Follow all instructions and
safety messages.

AVOID DEATH OR SERIOUS INJURY

Follow instructions before operating or servicing the
attachment.  Read  and  understand  the  Operation  &
Maintenance  Manual  for  the  attachment.  Follow
warnings  and  instructions  in  the  manuals  when
making repairs, adjustments or servicing. Check for
correct function after adjustments, repairs or service.
Untrained operators and failure to follow instructions
can result in death or serious injury.

•

Never service Geith attachments without instructions.

•

Cleaning and maintenance are required daily.

•

Welding or grinding painted parts should be done in
well ventilated areas.

•

Wear a respirator mask when grinding painted parts.
Toxic dust and gas can be produced.

•

Never service or adjust attachment with the
machine’s engine running unless instructed to do so
in this manual.

•

Avoid contact with leaking hydraulic fluid or diesel fuel
under pressure. It can penetrate skin or eyes.

•

Keep body, jewelry and clothing away from moving
parts, electrical contact, and hot parts.

•

Wear eye protection to guard from compressed
springs, fluids under pressure and flying debris when
engines are running or tools are used. Use eye
protection approved for welding.

•

Wear protective clothing. If acid contacts body, flush
well with water. For eye contact, flush well and get
immediate medical attention from a physician familiar
with this injury.

WARNING

«
...
11
12
13
14
15
...
»

Содержание QC100 H1



























































Отзывы:

Нет отзывов

Похожие инструкции для QC100 H1

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: JAC Страницы: 100

Бренд: Datavideo Страницы: 50

Бренд: Waterous Страницы: 90

Бренд: Campbell Страницы: 14

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Nektar Страницы: 3

Бренд: Eaton Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды