Gehl PowerBox 1639 Скачать руководство пользователя страница 40

Страница: 40 / 66

PROBLEM

POSSIBLE CAUSE

REMEDY

Insufficient hydraulic

Relief Valve pressure setting

Readjust Valve pressure setting.

Cylinder power

decreased.

Cylinder internal oil leakage

Replace seals.

Cylinder piston or seals defective.

Replace piston or seals.

Control Valve internal oil leakage.

Replace entire Valve housing.

Hydraulic Cylinder

Cylinder seals defective.

Replace seals.

external oil leakage

Cylinder rod damaged.

Replace rod.

Piston does NOT

Oil temperature is abnormally high.

Lower the oil temperature.

move smoothly.

Air being taken into system.

Replenish oil and retighten
suction connections.

Seals defective

Replace seals.

HYDRAULIC CYLINDERS

PROBLEM

POSSIBLE CAUSE

REMEDY

Starter will NOT turn.

Keyswitch is in OFF or RUN position.

Turn Keyswitch to START position.

Speed control not in OFF position.

Move speed control to OFF position.

Faulty wiring and/or terminations, or

Troubleshoot circuit and repair.

Fuse open.

Faulty Starter switch

Replace.

Battery NOT adequately charged.

Recharge.

Battery discharges and/

Terminal or cables are loose or

Clean terminals and cables and

or will NOT recharge.

corroded, Battery is defective, and/or

retighten or replace Battery; have

Alternator (or Regulator) defective.

dealer check Alternator

(or regulator).

Battery electrolyte level low.

Replenish with distilled water.

Alternator defective.

Replace or repair.

Operating Horn, etc.

Fuse blown.

Check cause ,correct and/or replace

does NOT function.

Fuse

Charge Indicator

Faulty Alternator

Replace.

does NOT activate
before Engine starts.

Battery is NOT sufficiently charged.

Recharge.

ELECTRICAL SYSTEM

907389/AP297

Printed In U.S.A.

Discount-Equipment.com

Содержание PowerBox 1639



































































Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды

Gehl PowerBox 1639, Руководство оператора

Результаты поиска

Содержание PowerBox 1639

Отзывы:

Похожие инструкции для PowerBox 1639

Бренды по названию

Популярные бренды