Gehl PowerBox 1639 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 66

background image

GENERAL INFORMATION

NOTE:

The Maintenance Log chapter in this

manual has provisions for recording the dates and
Hourmeter readings after lubrication or other ser-
vice has been performed; use those spaces to
keep a log for maintaining a current service inter-
val record. Proper routine lubrication is an impor-
tant factor in preventing excessive part wear and
early failure.

LUBRICANTS

The following chart lists the locations, temperature
ranges and types of recommended lubricants to be used
when servicing this machine. Also refer to the separate
Engine Manual (provided) for additional information
regarding recommended Engine lubricants, quantities
required and grades.

NOTE:

Refer to Operator Services topic in

Service Chapter of this manual for detailed infor-
mation regarding periodical checking and replen-
ishing of lubricants.

GREASING & LUBRICATION

Refer to the following pages for locations and greasing
frequencies. Wipe dirt from the grease fittings before
greasing them to prevent contamination. Replace any
missing or damaged fittings. To minimize dirt build-
up, avoid excessive greasing.

Chapter 7

LUBRICATION

CAUTION

NEVER attempt to lubricate or service this unit
when any part of the machine is in motion.
ALWAYS BE SURE to exercise the MANDA-
TORY SAFETY SHUTDOWN PROCEDURE
(page 10) BEFORE proceeding to lubricate or
service this equipment.

Hydraulic System Reservoir

Use SUNVIS 846, or equivalent

which contains anti-rust, anti-foam and anti-

oxidation additives & conforms to ISO VG46.

Capacity:

20 Gallons (75.7 liters)

All Grease Fittings

Use No. 2 Lithium-based Grease

Engine Crankcase Oil

Ambient Temperature

Grade*

Below 32oF (0C)

SAE 10 or 10W-30

32-77oF (0-25C)

SAE 30 or 10W-30

Above 77oF (25C)

SAE 40 or 20W-40

*Service Classification: API - CD/CE/CF-4

Capacity

4 Quarts (3.8 liters) - Gas Engine

6.9 Quarts (6.5 liters) - Diesel Engine

Torque Hubs Gear Oil

Use API-GL-5 80w90

Capacity (each Hub):

17 ounces (481 grams)

Printed In U.S.A.

33

907389/AP297

NOTE:

Always dispose of waste lubricating oils,

anti-freeze and hydraulic fluids according to local
regulations or take them to a recycling center for
disposal. Do NOT pour them onto the ground or
into a drain.

Discount-Equipment.com

«
...
29
30
31
32
33
...
»

Содержание PowerBox 1639



































































Отзывы:

Нет отзывов

Похожие инструкции для PowerBox 1639

Бренд: K&K Страницы: 8

Бренд: Raymarine Страницы: 24

Бренд: Hansen Страницы: 72

Бренд: AAT Страницы: 16

Бренд: AAT Страницы: 40

Platinum Series

Бренд: Dairy Tech Страницы: 38

Бренд: H&S Страницы: 34

Бренд: QAL Medical Страницы: 42

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренд: Nitecore Страницы: 4

Бренд: Vapotherm Страницы: 32

Бренд: Vanguard Instruments Страницы: 47

Бренд: Yamaha Страницы: 5

Бренд: Tieline Страницы: 359

Бренд: EuroLite Страницы: 2

Бренд: Ebyte Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды