gefran GTF 120 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 40

gefran GTF 120 Скачать руководство пользователя страница 3

3

80960G_MHW_GTF_05-2019_ENG

1.3

P

reliminary

instruction

Read the following preliminary instructions before

installing and using the GTF modular power

controller. This will make start-up faster and

avoid some problems that could be mistakenly

interpreted as malfunctions or limitations of the

controller

Immediately  after  unpacking  the  unit,  check  the  order  code
and the other data on the label attached to the outside of the
container.
Write them on the following table.
This  data  must  always  be  available  and  given  to  Gefran
Customer  Care  representatives  are  available  if  technical
service is needed.

SN

(Serial number)

CODE

(Product code)

TYPE

(Order code)

SUPPLY

(Power Supply)

VERS

(Firmware version)

Check that the controller is in perfect condition, was not
damaged during shipment, and that the package also contains
the “Configuration and Programming” manual.
Immediately report any errors, shortages, or signs of damage to
your Gefran dealer.
Check that the order code matches the configuration requested
for the intended application by consulting the section:
“Technical-Commercial Information.”

Example

GTF

90

480

0

1

0

M

Model

Nominal current

Nominal voltage

Control option, Absent

Diagnostic option: HB

Fuse: absent

Serial Modbus

See paragraph 2.1 “ Dimensions and mounting” before installing
the GTF on the machine/host system control panel.
To configure the PC use the SW Gefran GF-Express kit and the
relative connection cable.
For the order code, see Section: “Technical-Commercial
Information”.

Users and/or system integrators who want detailed

information on serial communication between

Gefran standard and/or industrial PCs and Gefran

Programmable Instruments can access Technical

Reference Documents on serial communication

and MODBus protocol, etc., in Adobe Acrobat

format on the Gefran website www.gefran.com:
• Serial Communication
• MODBus Protocol

Before calling Gefran Customer Care in case of assumed mal-
functions, please see the Troubleshooting Guide in the “Mainte-
nance” section and, if necessary, the F.A.Q. (Frequently Asked
Questions) section on the Gefran website www.gefran.com

«
1
2
3
4
5
...
»

Содержание GTF 120









































Отзывы:

Нет отзывов