background image

3

Technical data

3.1

Technical data

Refer to the following tables for the key technical data of the valve:

Technical data: Valve

Designation

Description

Size

4" to 6" OD

Material of product contact parts

Stainless steel 1.4404

Fitting position

Any position, if valve and pipe system can drain
properly

Technical data: Ambient temperatures

Designation

Description

Valve

0 to 45 °C (32 ... 113 °F), standard
< 0 °C (32 °F): Use control air with low dew
point. Protect valve rods against freezing.
< −15 °C: no solenoid valves in the control top

Initiator

-20 to +80 °C (-4 ... +176 °F)

Product temperature and operating temperature depending on the sealing material

Technical data: Compressed air supply, product pressure

Designation

Description

Air hose

Metric

Material PE-LD Outer-Ø 6 mm +/- 0.1 mm
Inside Ø 4 mm

Inch

Material PA outer-Ø 6.35 mm +/- 0.1 mm
Inside Ø 4.3 mm

Control air

acc. to ISO 8573-1

Solid particle content:

Quality class 6
Particle size max. 5 µm
Particle density max. 5 mg/m

3

Water content:

Quality class 4
max. dew point +3 °C
If the unit is used at higher altitudes or at low
ambient temperatures, the dew point must be
adapted accordingly.

Oil content:

Quality class 3,
preferably oil free
max. 1 mg oil to 1 m

3

 air

Technical data

Technical data

221BAL015386EN_1

 

01.11.2023

7

Содержание ECOVENT TEFASEP-Gold ECO E



















Отзывы: