GEA D-tec D Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 106

background image

10.5.1.2 Disconnecting the valve from the housing

Fig.21:

Disconnecting the valve from the housing

Caution!

Risk of injury due to moving valve parts.

► Do not touch the lantern (9).

Warning!

Spring tension in the valve

Danger of injury when opening the clamp connections on the actuator or on
the housing as the released spring pretension will suddenly lift the actuator.
► Therefore, release the spring tension before detaching the clamp
connections by pressurising the actuator with compressed air at max. 8 bar.

Tools required:

•

Open-ended wrench

Carry out the following steps:

1.

Turn the connection (0) with the angled screw-in connection and reduction
nipple in the piston stem.

2.

Vent actuator at connection (0) with compressed air, max. 8 bar.

®

The valve insert is raised.

Maintenance

Disassembling the valve

430BAL013307EN_8

48

04.08.2022

«
...
46
47
48
49
50
...
»

Содержание D-tec D











































































































Отзывы:

Нет отзывов

Похожие инструкции для D-tec D

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Lux Intelligent

Бренд: Advanced Страницы: 62

Бренд: intech 21 Страницы: 15

Бренд: Xsens Страницы: 17

VENMAR ADVANCED TOUCHSCREEN CONTROL

Бренд: vanEE Страницы: 4

Бренд: GOAL ZERO Страницы: 52

Бренд: Variotech Страницы: 24

Бренд: DEUTSCHMANN AUTOMATION Страницы: 30

Бренд: QUANT Страницы: 24

Бренд: Parker Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды