GE XMT868 Скачать руководство пользователя

Страница: 3 / 7

913-326A

3 of 7

November 2005

Configuration Utility
Setup

The following is an example setup using National Instruments
Configuration Utility v3.1.

Figure 2 below shows the Configuration Utility with an

XMT868

flow

meter on the network (GE Flow-XMT).

Figure 2: Configuration Utility Setup Example

Note:

The following procedures assume that the device has been placed
in the OOS (out-of-service) mode before executing.

Selecting the Desired
Measurements

To set the measurement unit for each AI:

Double click on the

FLOW

Transducer Block (in the tree under

GEFlow-XMT

Select the

Others

tab and open the drop down list for the

PRIMARY_SELECTOR

and

SECONDARY_SELECTOR

(see Figure 3 on

page 4).

Choose the unit from the list (see Figure 3 on page 4).

This unit will correspond to the unit that is available in the AI block for
network connection. The

PRIMARY_SELECTOR

unit will correspond to

ANALOG_INPUT_1

and the

SECONDARY_SELECTOR

will correspond to

ANALOG_INPUT_2

Содержание XMT868








Результаты поиска

Содержание XMT868

Отзывы:

Похожие инструкции для XMT868

Бренды по названию

Популярные бренды

GE XMT868, Быстрый старт

Результаты поиска

Содержание XMT868

Отзывы:

Похожие инструкции для XMT868

Бренды по названию

Популярные бренды