manualshive.com logo in svg

GE UUC112WC Series, Руководство по обслуживанию, Страница: 3 / 16

Поделиться
Скачать
GE UUC112WC Series Скачать руководство пользователя страница 3

CONNECT SERIES SERVICE MANUAL

1

ENGLISH

Safety Notifications

PROHIBITED:

• Do not pierce or burn.
• Please note that refrigerant may be odorless.
• The appliance shall be stored in a room without 

continuously operating ignition sources (For 

example: open flames, an operating gas appliance 

or an operating electric heater).

• Indoor unit adopts special joints that can’t be 

detached. The installation method is the same 

with the common joints. Because the joint can’t be 

detached and if it is leaking; it must be cut out and 

replaced with a braze joint.

• Using unsuitable parts or tools may lead to electric 

shock or fire hazard.

• Please ventilate the room immediately if refrigerant 

leaks during maintenance. Heavy leakage may lead 

to breathing difficulty, severe injury or death.

• Disconnect power before disassembling the 

appliance for maintenance.

• The appliance should be maintained and cared 

by authorized technical personnel with necessary 

qualifications.

Maintenance Safety

WARNING:

• If the unit location is more than 6 feet high, please 

wear a safety helmet, gloves and a safety belt.

• Never mix any other substances except the 

specified refrigerant into the refrigerant circuit.

• Check the location to see if the weight can be 

properly supported before installing the unit.

• Please test the system for leaks prior to charging. 

Leaks discovered after the unit start up require 

refrigerant pump-down, leak repair and recharging. 

Do not allow refrigerant to leak into unventilated 

spaces.

• Prepare suitable tools and protectors.
• Please isolate all power to the system while making 

repairs and performing maintenance.

NOTICE:

• This unit requires a proper earth ground per local 

and national electrical codes.

• Never repair the unit with wet hands. Operating the 

unit with wet hands may lead to electric shock.

• Isolate all power sources before cleaning the unit.
• All field installed wiring must conform to local and 

national electric codes.

• Brazing, welding and cutting must de done in 

properly ventilated areas.

• Gas appliances, heaters and other fire sources 

should be kept away from the installation and 

maintenance site.

• Maintenance should be done according to 

manufacturer’s instructions.

OBSERVED:

• Check all condensate drain outlets during 

maintenance and operational checks.

• Unit should be installed level and on a surface that 

will sufficiently support it’s weight.

• Disassembly of the unit, handling of the refrigerant, 

oil and accessories should all be done according to 

applicable local rules and regulations.

Operation Safety

PROHIBITED:

• Never try to modify the unit, otherwise, it may 

cause electric shock, overheat or fire hazard.

• Replace all wires that have worn or damaged 

insulation.

• This equipment must have a dedicated electrical 

circuit and service disconnect switch.

WARNING:

• Maintain a regular schedule for presentative 

maintenance.

NOTICE:

• Do not remove the fan cover while the unit is 

running.

• Use soap and water only to clean the unit. Do not 

use any solvents to clean the control panel.

• Isolate all power to the system before cleaning the 

unit.

Содержание UUC112WC Series

















Отзывы:

Нет отзывов