GE TMO2D Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 102

background image

TMO2D Digital Display User’s Manual

27

Chapter 4. Basic Programming

4.4.6 Set Display?

Although this feature is not commonly used, the TMO2D, when used with the TMO2, can display compensation values
for pressure or the percentage of background gas. For the analyzer to display these values, the TMO2 must include
external compensation. In addition, you must enable either background or pressure compensation through the

Calibration

menu (see page 37) in the

Select Compensation

submenu (page 38). If neither pressure nor background

compensation is enabled, a “Comp not enabled” message will appear.

4.4.7 Set Communications?

Baud Rate: The display contains a bi-directional, industry-standard RS-232C serial port that enables users to operate
the instrument remotely with a keypad or computer that supports the RS-232C protocol. All keypad operations, and
most display operations, can be performed remotely through this port. (See page 20 for operation instructions.)

The display supports the communication rates of 9600, 4800, 2400, 1200 and 300 baud. The default setting is 9600
baud. Other parameters are fixed at 8 bits, 1 stop bit, no parity.

Note:

The 300-baud setting is provided for compatibility with older equipment; however, the use of 300 baud greatly
limits the computation speed of the TMO2D, and its use is not recommended.

The

Set Communications?

submenu enables you to select both the baud rate and the update rate, when they

communicate with the TMO2D through the RS-232 port.

SETUP MENU
Set Display?

Press [YES] to set the display.

Display Compensation
[[NO]NE] pres bkgd

Use the [NO] or arrow keys to move the brackets to the desired entry. Press [YES] to
confirm the entry and exit.

SETUP MENU
Set Display?

Press [NO] to proceed to the next submenu.

SETUP MENU
Set Communications?

Press [YES] to enter the submenu.

SET COMMUNICATIONS
Set Baud Rate?

Press [YES] to enter the baud rate.

SELECT BAUD RATE
9600 baud?

Use the [NO] or arrow keys to scroll through the choices.

SELECT BAUD RATE
4800 baud?

SELECT BAUD RATE
2400 baud?

SELECT BAUD RATE
1200 baud?

«
...
33
34
35
36
37
...
»

Содержание TMO2D







































































































Отзывы:

Нет отзывов

Похожие инструкции для TMO2D

Бренд: Xiaomi Страницы: 36

TYSP50P8WK - Speakers For 50IN Plasma...

Бренд: Panasonic Страницы: 1

Бренд: Panasonic Страницы: 56

Бренд: AG Neovo Страницы: 53

Бренд: ViewSonic Страницы: 2

Бренд: V-Tec Страницы: 4

Бренд: I-Tech Страницы: 30

Бренд: displayit Страницы: 6

Бренд: NewLine Страницы: 72

VG2227WM - 22" LCD Monitor

Бренд: ViewSonic Страницы: 25

ELITE GRAPHIC WALL EGW-66

Бренд: Abex Exhibits Страницы: 3

Бренд: Ubiquiti Страницы: 3

Бренд: InMotion Страницы: 17

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды