LED Driver
Wire connections
Cap all unused wires
Refer to the LED Driver Installation Instructions for
more information on connecting the LED Driver.
Electrical Connections
1
2
3
4
Strip the ends of the wire 1/2-inch (13 mm) on the
modules (white and red) of adjacent columns that
you want to connect.
Use UL approved wire connectors (twist-on or
in-line connectors) and 18 AWG (0.82 mm
2
) wire to
connect the corresponding wires.
Strip the end of the wire 1/2-inch (13 mm) on the
first column of modules and connect to the output
of the LED Driver. Output connections must be
red-to-red and white-to-black.
Remote Mounting Distance
Loading Chart
Troubleshooting
Symptom
Row of modules does not light
All modules do not light
Individual modules do not light
Modules are dim
• Check wire connections to LED Driver to ensure red-to-red and white-to-white connections.
• Check row-to-row polarity connections.
• Check input voltage and check LED Driver input/output connections.
• Check wire connection attachment and polarity of wires.
• Ensure the overall length of modules does not exceed the maximum load for the LED Driver.
• Ensure the length of the supply wire is equal to or below the recommended remote mounting
distance (see remote mounting distance chart above).
Solution
LED Driver
Minimum Loading
Maximum Loading
79045 (GE080/MV/D24T1-A)
1 Module
30 Modules/20 ft. (6.1m)
67825 (GEPS24-100UGL-IP)
1 Module
36 Modules/24 ft. (7.3m)
62189 (GE180/MV/24T1-C)
1 Module
33 Modules/22 ft. (6.7m) per Bank; 66 Modules/44 ft. (13.4m) per Driver
LED Driver
18 AWG/0.82 mm
2
Supply Wire
16 AWG/1.31 mm
2
Supply Wire
14 AWG/2.08 mm
2
Supply Wire
12 AWG/3.31 mm
2
Supply Wire
67825 (GEPS24-100UGL-IP)
62189 (GE180/MV/V24T1-C)
79045 (GE080/MV/D24T1-A)
1-30 ft. (0.3-9.1m)
1-50 ft. (0.3-15.2m)
1-80 ft. (0.3-24.4m)
1-120 ft. (0.3-36.6m)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class [A] RFLD complies with the
Canadian standard ICES-003. Ce DEFR de la classe [ A ] est conforme á la NMB-003 du Canada.
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
www.gelighting.com
GE and the GE Monogram are trademarks of the General Electric Company. All other trademarks are the property of their respective owners. Information provided is subject to
change without notice. All values are design or typical values when measured under laboratory conditions. GE Lighting is a business of the General Electric Company. © 2016 GE.
ARCH015 (Rev 01/27/16)
GEH-5988 35-201578-180
