background image

12

49-3000244 Rev 5

V

E

N

T

IN

G Venting

Venting the Dryer

For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run longer if it is 
not vented to the specifications below. Carefully follow the details on Exhausting in the Installation Instructions.

  Use only rigid metal 4” diameter ductwork inside the dryer cabinet. Use only rigid 

metal or UL listed flexible metal 4” diameter ductwork for exhausting to the outside.

  Do not use plastic or other combustible ductwork.

  Use the shortest length possible.

  Do not crush or collapse.

  Avoid resting the duct on sharp objects.

 

 Venting must conform to local building codes.

This dryer MUST be exhausted to the outdoors.
Use only 4” rigid metal ducting for the home exhaust duct.
Use only 4” rigid metal or UL-listed dryer transition duct to connect the dryer to the home exhaust.

DO NOT

 use a plastic vent.

DO NOT

 exhaust into a chimney, kitchen exhaust, gas vent, wall, ceiling, attic, crawl space, or 

concealed space of a building.

DO NOT

 install a screen in or over the exhaust duct.

DO NOT

 install a booster fan in the exhaust duct.

DO NOT

 use duct longer than specified in the exhaust length table.

Failure to follow these instructions can result in death or fire.

- Fire Hazard

Correct 

Venting

Incorrect 

Venting

Vent Health

Is a diagnostic test to verify the status of the venting system. 

NOTE:

 To run the test, ambient temperature must be 

below 85°F (if temperature is above 85°F the test will be invalid and the main display will show “00”).

NOTE:

 On some models this features is only available through the GE Appliances SmartHQ App.

To enter Vent Health test mode:

1

 Ensure the drum is empty.

2

 Ensure the lint filter is clean.

3

 Press and hold the 

Time

 and 

Level

 buttons for 3 seconds.

4

 Close the door and press 

Start

.

After the test is run, the display will show a number. Use the table below to understand the result and the action needed.

Main Display

LED Display

Result

Action*

01

OFF

Clean/Normal

Your house vent is in good condition 

and no action is required.

02

OFF

May need attention

Your house vent condition may affect your 

dryer’s performance. Check and clean 

or make adjustments to improve.

03

Vent Blocked

Blocked

Your house vent is highly restricted and 

is affecting your dryer’s performance. 

Clean and/or make needed 

adjustments to improve.

*

Also see 

Interior and Duct

 in the 

Care and Cleaning

 section.

Содержание PTD90EBMTRS





















Отзывы: