GE PSW23PSWSS - 23.2 cu. Ft. Refrirator, Инструкция для владельца и по установке

Страница: 15 / 132

About the ice and water dispenser.
(on some models)
ge.com
To Use the Dispenser
Select CUBED, CRUSHED or WATER.
Press the glass gently against the top of the
dispenser cradle.
The spill shelf is not self-draining. To reduce
water spotting, the shelf and its grille should be
cleaned regularly.
If no water is dispensed when the refrigerator is first
installed, there may be air in the water line system. Press
the dispenser arm for at least two minutes to remove
trapped air from the water line and to fill the water
system. To flush out impurities in the water line, throw
away the first six glassfuls of water.
CAUTION: Never put fingers or any other objects into
the ice crusher discharge opening.
Locking the Dispenser
Press the
LOCK
pad for 3 seconds to lock the
dispenser and control panel. To unlock, press
and hold the pad again for 3 seconds.
Dispenser Light
The
LIGHT
pad turns the
night light
in the
dispenser on and off. The light also comes on
when the dispenser cradle is pressed. On some
models, if this light burns out, it should be
replaced with a 6 watt 12V maximum bulb.
Door Alarm
Use
Door Alarm
to sound if either door is open
for more than 3 minutes. The alarm will stop
once the door is closed. For LCD models, a
popup screen will appear. The alarm can be
silenced by touching the LCD screen.
LCD Models:
Access By:
Home > Options > Information and
Settings > Settings > Door Alarm
Access By:
Pressing
ON
.
Deactivate By:
Pressing
OFF
.
Non-LCD Models:
Press the
DOOR ALARM
pad until the indicator
light comes on.
Spill Shelf
Consumer Support
Tr
oubleshooting T
ips
Operating Instructions
Safety Instructions
Installation Instructions
Precise Fill
(on some models)
Quick Ice
This water dispenser is equipped with a feature
called “precise fill.” This feature allows you to
choose a precise amount of water (cups or
ounces) that you would like dispensed. Pints
and Liters are also available for LCD models.
LCD Models
Access By:
Home > Options > Dispenser
Options > Precise Fill > Set Amount
Activate By: Using the arrow buttons to select
the desired amount. Press
MORE UNITS
to select
between CUPS, OUNCES, PINTS or LITERS.
Non-LCD Models
Press the WATER pad.
Press the
CUPS
or
OUNCES
pad.
Select the precise amount of water you
would like dispensed.
If you selected OUNCES,
press the arrow
pads on either side of the display to
select the number of ounces you
would like to have dispensed between
1–99 ounces.
If you selected CUPS,
press the arrow
pads on the left of the display to select
the whole cups (1–16 cups) and/or
the arrow pads on the right side of the
display to select fractions of a cup
(1/4–3/4 cups).
Press the cup against the cradle and water
will begin dispensing. It will automatically
stop when the amount set has been
dispensed. The display will show there
is no water left to dispense, then reset.
NOTE: Do not leave the dispenser unattended when
water is being dispensed.
If you would like to stop dispensing water
before the specified amount has been
dispensed, just remove the cup from the
cradle. The display will show the amount
left to dispense.
When you need to speed up ice production, use
the
Quick Ice
feature. While this feature is turned
on, the freezer fan runs continuously for 48 hours,
or until the feature is turned OFF. During this
period, ice production will increase up to 40%.
Models with the integrated ice feature system
require at FIRST USE at least half an 8 oz. glass
of ice to be dispensed every 6 to 12 hours. This
will help the icemaker fill the bucket properly
so that dispensing is better.
How to Use
LCD Models:
Access by:
Home > Options > Freezer Options >
Quick Ice
Activate by:
Pressing
ON
.
Deactivate by: Pressing OFF .
Non-LCD Models:
Press the QUICK ICE pad to turn the feature ON.
Press the pad again to turn the feature OFF.
15