GE Profile PDWF400P Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

��

��

��

��

STEP 3 – CHECK DOOR BALANCE

• With dishwasher on the wood skid, check the door balance

by opening and closing the door.

• If the door drops when released, increase the spring tension.

If the door rises when released, decrease the tension.

• There are two types of counter balance and therefore two

methods of adjustment. Identify which counter balance is

present and adjust tension accordingly. Please note: if there

are 3 holes on the cable, use the cable to adjust; if there is

one hole on cable use the tub leg to adjust.

Figure H

7

Dishwasher Installation

CAUTION:

Do not remove wood base until you are ready to install

the dishwasher. The dishwasher will tip over when the

door is opened if the wood base is removed.

Figure G

STEP 2 – INSTALL TRIM PIECES

In this step, you will need the trim pieces set aside in Step 1.

• Press top trim piece onto top of tub ﬂ ange. Start with the

right edge and work your way to the left.

• Repeat process with the left and right trim pieces working

from the top down.

• Open and close the door to check that trim does not bind and

does not interfere with door latch or door hinges.

Trim Strip

Trim

Strip

Trim

Strip

05A-1183U

Type 2

–

Three hole cable

Adjust tension by moving spring hook to one of the three holes
on the pulley cable.

Figure I

Increase

Tension

Decrease

Tension

Use This

Mounting

Hole

05A-1183P

After adjusting spring tension, open and close the door to
make sure the door operates smoothly. If the door is hard
to move or if the spring cable binds, check the routing of
the spring cable. The cable should be routed between the
shoulders of the pulley cable roller. If the cable is off the roller:
latch door, remove spring tension and route the cable between
the shoulders of the roller. See Figure J.

Type 1

–

One hole cable

Adjust tension by moving spring hook to one of the three holes
on the tub leg.

STEP 1 – LOCATE INSTALLATION ITEMS

• Locate the items in the installation package and set aside for

use in the listed steps.

• Trim pieces – Step 2

• Junction box cover – Step 7 or Step 18

• Drain hose and clamp – Step 10

• Screw Kit – Step 15

• Drain hose hanger – Step 17
• Owner’s Manual – Step 19 and Step 24
• Hard Water test strip – Step 21
• Sound upgrade kit (selected models) – Step 22
• Product samples and/or coupons – Step 24

Figure J

Correct Spring

Cable Routing

Shoulder

Pulley

Incorrect Spring
Cable Routing

«
...
5
6
7
8
9
...
»

Содержание Profile PDWF400P

















Отзывы:

Нет отзывов