manualshive.com logo in svg

GE Profile PDW7300N, Руководство по установке

Поделиться
Скачать
GE Profile PDW7300N Скачать руководство пользователя страница 8

STEP 12– INSTALL SIDE-MOUNT

BRACKETS (included with 

some models)

Skip this step if underside of countertop is wood or

wood-like material.

• Install side-mount brackets if underside of countertop is 

granite or similar material that will not accept wood screws.

• Locate the side mount bracket kit set aside in Step 1 if it was 

provided with this model. Otherwise, see Note below.

Note: 

The brackets are available for purchase when

needed for models not factory equipped with the side mount 
kit. Order part GPF65 from your authorized GE Appliance 
Dealer.
• Fasten the left-hand bracket to the left side 

of the dishwasher frame. Fasten the 
right-hand bracket to the right side of the 
dishwasher frame, using the #8 pan-head 
screws included with the kit. Refer to 
Step 15, Figure U for orientation 
and placement.

Installation Instructions

Figure Q

STEP 13– PUSH DISHWASHER INTO 

FINAL POSITION

Tip:

 Check tub insulation blanket, if equipped. It should be 

positioned so it is not “bunched up” or interfering with door 
springs. Check by opening and closing door.
• Push dishwasher into the cabinet. The edges of the 

dishwasher door should be behind the cabinet frame and 
evenly aligned with the front face of cabinet doors.

Tip:

 Avoid unnecessary service charges. Carefully open and 

close the door to ensure the door panel is not catching or 
rubbing on the cabinet frame.

8

STEP 14–LEVEL DISHWASHER

IMPORTANT

– 

 Dishwasher must be level for proper 

dish rack operation and wash performance.
• Place level on door and lower rack track as shown. Check to 

make sure that the dishwasher is level left to right and front 
to back.

• Level the dishwasher by adjusting the four leveling legs 

individually. Refer to Figure S below.

• If adjustment to the right rear leveling leg is required, loosen 

junction box bracket screw (through the access hole) and 
rotate bracket clockwise. Be sure to tighten screw when 
leveling is completed.

Tip:

 Pull lower rack out, about halfway. Check to be sure the 

rack does not roll forward or back into dishwasher. If the rack 
rolls in either direction, the dishwasher must be leveled again.
• If door hits tub, the dishwasher is not installed correctly. 

Adjust leveling legs to align door to tub.

Figure R

Figure S

Door

Fits and 

Swings

Back

Behind

Cabinet

Frame

Correct

Alignment

Door Catches

on Cabinet Frame

Incorrect

Alignment

05A-1183X

Check

Level

Left-

to-Right

Check

Level 

Front- 

to-Back

923-10G

���������

Side-Mounting 

Brackets on 

some models

06E-1174E

Loosen junction box

bracket screw and

rotate bracket out of

the way to access the

right rear leveling leg.

Tighten screw when

leveling operation is

completed.

Junction Box Bracket

Turn Legs 

to Adjust 

Содержание Profile PDW7300N













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды