GE PEB2060SMSS - Countertop Microwave Oven, Руководство по установке, Страница: 2 / 8

❒
CUTOUT DIMENSIONS
1
2
* Min. depth with receptacle outside cabinet 19
1 ⁄
2
″
Min. depth with receptacle inside cabinet 22 ″
120 volt-60 Hertz grounded power receptacle
Installation Instructions
Models 27
″
30
″
Height 16 3 ⁄
4
″ 16 3 ⁄
4
″
Width 25 1 ⁄
2
″ 25 1 ⁄
2
″
Depth (min.)* 19 1 ⁄
2
″ or 22 ″ 19 1 ⁄
2
″ or 22 ″
WARNING
—
This trim kit uses air flow
from the top, bottom and sides of the trim frame.
Blocking the air flow can cause the microwave to
function improperly and may cause damage to
the microwave.
Allow a 1 ″ clearance beyond the edge of the trim
frame to provide proper air flow.
On 27 ″ models, allow 1 1 ⁄
8
″ at the top, 11 ⁄
16
″ on the sides
and 1 1 ⁄
4
″ at the bottom for overlap of the Trim Frame
over the edges of the cutout.
On 30 ″ models, allow 1 1 ⁄
8
″ at the top, 2 1 ⁄
16
″ on the sides
and 1 1 ⁄
4
″ at the bottom for overlap of the Trim Frame
over the edges of the cutout.
FOR INSTALLATION ABOVE A
BUILT-IN OVEN:
Microwave oven should be installed on a 3/8 ″ plywood
base and supported by 2x4 or 1x2 equivalent runners
on all sides. Base must be capable of supporting a
minimum of 100 lbs (45.3 kg).
Draw a line on the cutout floor at the center of the
cutout, and extend the line 1/2
″ down the face of
the cabinet.
Draw a line on the top front face of the cabinet
at the center of the cutout. The line should extend
1/2
″ up the face of the cabinet. This center line will
be used for mounting the top bracket (see step 7).
Fold or cut the front edge of the template, along the
front guide line. Place the template flush along the
front edge of the cutout floor, aligning the center line
of the template with the center line of the cutout
floor. Mark the center positions with an awl or center
punch for the anti-tip brace location as shown.
Drill two holes for the anti-tip brace.
Install the anti-tip brace onto the cutout floor using
two round-head screws.
B
C
D
E
D
D
Round-head
screws (2)
Anti-Tip Brace
❒
INSTALL THE ANTI-TIP BRACE 2
Depth
Height
1 1 ⁄
4
″ Overlap
Width
1 1 ⁄
8
″ Overlap
1 ″ Clearance
beyond trim frame
(on all sides)
3 ″ Min.
27 ″ Models: 11 ⁄
16
″ overlap
30 ″ Models: 2 1 ⁄
16
″ overlap
A
DIMENSIONS:
A = 1
1
⁄
2
″
B = 3
″
C = 18
3
⁄
16
″
D = 1/2
″
Bottom of trim kit
must be minimum
of 36 ″ from floor
1 ′ = 0.3 m
1 ″ = 2.5 cm