GE PanaFlow MV80 Скачать руководство пользователя | Manualshive

Страница: 24 / 164

background image

Chapter 2. Installation

12

PanaFlow™ MV80 & MV82 User’s Manual

2.2.2 Installing Wafer-Style Flowmeters

Install the wafer-style meter between two conventional pipe flanges of the same nominal size as the flowmeter (see

below). If the process fluid is a liquid, make sure the meter is located where the pipe is always full. This may

require locating the meter at a low point in the piping system.

Note:

Vortex flowmeters are not suitable for two-phase flows, such as liquid and gas mixtures.

For horizontal pipelines having a process temperature above 300° F, mount the meter at a 45 or 90-degree angle to
avoid overheating the electronics enclosure. To adjust the viewing angle of the enclosure or display/keypad, see

“Display/Keypad Adjustment (All Meters)” on page 30

“Enclosure Adjustment (Series MV80 Only)” on page 31

.

Figure 6: Wafer-Style Flowmeter Installation

When installing the meter make sure the section marked with a flow arrow is positioned upstream of the outlet, with the
arrow head pointing in the direction of flow. (The mark is on the wafer adjacent to the enclosure mounting neck.) This
ensures that the sensor head is positioned downstream of the vortex shedder bar and is correctly aligned to the flow.
Installing the meter opposite this direction will result in completely inaccurate flow measurement.

CAUTION!

When using toxic or corrosive gases, purge the line with inert gas for a minimum of four

hours at full gas flow before installing the flowmeter.

FLOW

Enclosure and

display/keypad
are adjustable to suit

most viewing angles.

Incorrect gasket position!
Do not allow any gasket
material to extend into
the flow profile.

Shedder bar (bluff body)
is positioned upstream
of the sensor.

«
...
22
23
24
25
26
...
»

Содержание PanaFlow MV80





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PanaFlow MV80

Бренд: WAGER Страницы: 22

Бренд: Cablescan Страницы: 58

Бренд: ICS Страницы: 2

Бренд: CAISSON Страницы: 5

Бренд: Keithley Страницы: 201

Бренд: Lumel Страницы: 32

Бренд: JAMAR Technologies Страницы: 4

Бренд: Jamar Страницы: 60

Бренд: X-Rite Страницы: 50

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 48

Бренд: Major tech Страницы: 16

Бренд: Zoetis Страницы: 2

Бренд: Pasco Scientific Страницы: 11

Бренд: ColorLite Страницы: 68

Бренд: MULTISPAN Страницы: 2

Бренд: EUPRY Страницы: 6

Бренд: REED Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды