GE On-line VH Series Скачать руководство пользователя

Страница: 17 / 22

Critical Power

Modifications reserved

Page 17/22

GE_UPS_OPM_VHU_208_2K0_3K0_XUS_V010.docx

Operating Manual

VH2000-3000 208V UL

4.5

USE: SETUP MODE

The setup mode can only be entered if the UPS is in ‘standby’ -mode: connected to a live wall outlet and switched off (LED
'operation' blinks).

1

Press keypad 'O' and keep it pressed while pressing 'I' simultaneously. Release both buttons.

The setup sequence starts with the setup of the output voltage, indicated by a blinking LED ‘operation’.

Scroll through the four functions with keypad 'I', one of the LEDs ‘operation’, ‘on bypass’, ‘on battery’ or ‘alarm’ will
blink, indicating which function has been selected (see fig. 4.5).

Toggle the setting of the selected function by pressing switch 'O'. The LEDs on the LED bar ‘runtime capacity’ shows
the setting.

Store the new settings and leave the setup mode: press keypad '0' and keep it pressed while pressing 'I'
simultaneously. Release both buttons.

Fig. 4.5: Setup menu

*DEFAULT SETTING

60 Hz

auto*

50 Hz

Output

frequency

disabled*

enabled

Bypass

enabled*

disabled

Output voltage

230 Vac

208 Vac*

220 Vac

Phase – Neutral

reversal

240 Vac

Содержание On-line VH Series























Результаты поиска

Содержание On-line VH Series

Отзывы:

Похожие инструкции для On-line VH Series

Бренды по названию

Популярные бренды

GE On-line VH Series, Руководство пользователя

Результаты поиска

Содержание On-line VH Series

Отзывы:

Похожие инструкции для On-line VH Series

Бренды по названию

Популярные бренды