GE Mini COM Express 10 Скачать руководство пользователя страница 42

Страница: 42 / 82

5.2

Software

5.2.1

Memory and I/O Address Mapping

The system memory and I/O address mapping is controlled by the G-Series SoC. Refer to
the appropriate datasheet for further details.

5.2.2

SMBus Slave Devices

The G-Series SoC provides two SMBus masters with attached on-board slave devices.
SMBus 1 is also routed to the carrier board.

SMBus Devices

Bus

Device

Function

Address

CAT34TS02

SPD EEPROM

1010_000x

Temperature Sensor

0011_000x

I210

Ethernet Controller

Unused

5.2.3

C Slave Devices

The FPGA hosts an I

C bus controller.

C Devices

Device

Function

7-bit Address

AT24C32

Embedded EEPROM

1010_000x

AT24C32

User Data EEPROM

1010_001x

SB-TSI

Temperature Sensor

1001_100x

5.2.4

External Interrupts

All external interrupts are signaled through the serial IRQ or GPIO pins.

GFK-2896

Mini COM Express Type 10 Module mCOM10-L1500

For public disclosure

Содержание Mini COM Express 10



















































































Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды

GE Mini COM Express 10, Справочник по аппаратуре

Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды