GE Mini COM Express 10 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 82

background image

4.1.4

BIOS/UEFI Firmware

Refer to PICMG COM.0 R2.1
COM Express Module Base
Specification located at

www.picmg.org

.

The mCOM10-L1500 has an on-board 8 MByte SPI Flash ROM device that holds the
BIOS/UEFI firmware load. Alternatively, the module may be configured to boot from the
Flash located on the carrier board, on either the external SPI bus or LPC bus. This is
controlled by the carrier board using the

BIOS_DIS[0:1]#

straps.

UEFI Load

BIOS
DIS1#

BIOS DIS0# Chipset SPI_

CS1#

Chipset SPI_
CS0#

Carrier SPI_
CS#

SPI_
Descriptor

BIOS Entry

1

1

Module

Module

High

Module

SPI0/SPI1

1

0

Module

Module

High

Module

Carrier FWH (LPC)

0

1

Module

Carrier

SPIO

Carrier

SPI0/SPI1

0

0

Carrier

Module

SPI1

Module

SPI0/SPI1

4.1.5

Serial ATA

Two Serial ATA (SATA) controllers, integrated into the G-Series SoC, host mass storage
units on the carrier through the COM Express connector. SATA 2.x (3 Gbps) and 3.x (6
Gbps) are supported. A combined SATA activity indicator is also provided.

4.1.6

USB

The mCOM10-L1500 provides eight G-Series SoC USB controllers to host serial links
through the COM Express connector. All ports support USB 2.0, while ports 8 and 9 also
support USB 3.0 SuperSpeed. The following table provides port mapping between the
G-Series SoC and the COM Express connector.

USB Port Assignments

Port

USB Interface

Speed

0

Unused

N/A

1

Unused

N/A

2

mCOMe USB 2

FS, HS

3

mCOMe USB 3

FS, HS

4

mCOMe USB 4

FS, HS

5

mCOMe USB 5

FS, HS

6

mCOMe USB 6

FS, HS

7

mCOMe USB 7

FS, HS

8

mCOMe USB 0

FS, HS, SS

9

mCOMe USB 1

FS, HS, SS

4.1.7

Secure Digital or General-purpose I/O

The G-Series SoC provides a Secure Digital (SD) 3.0 compliant host controller wired
directly to the COM Express connector. Alternatively, these pins may be used as simple
general-purpose input/output (four pins each).

4.1.8

Audio

The G-Series SoC provides a basic PC speaker output, as well as a High Definition Audio
(HDA) controller wired to the COM Express connector.

System Architecture

GFK-2896 Hardware Reference Manual 25

For public disclosure

«
...
23
24
25
26
27
...
»

Содержание Mini COM Express 10



















































































Отзывы:

Нет отзывов

Похожие инструкции для Mini COM Express 10

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: IBM Страницы: 12

Бренд: K&K Страницы: 10

Бренд: Jetline Страницы: 58

Бренд: Velleman Страницы: 26

Бренд: Velleman Страницы: 32

Бренд: Velocity Страницы: 84

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: V2 Страницы: 48

Бренд: WAGO Страницы: 16

SaunaLogic SL2 Control

Бренд: Finnleo Страницы: 14

Бренд: S&C Страницы: 26

Бренд: Ashly Страницы: 1

Бренд: OneFex Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды