GE MDS 9710T Скачать руководство пользователя страница 27

Страница: 27 / 64

MDS 05-3305A01, Rev. E

MDS 4710/9710 Technical Manual

Error Messages

Below are possible error messages encountered when using the HHT:

UNKNOWN COMMAND

—The command was not recognized. Refer to the com-

mand description for command usage information.

INCORRECT ENTRY

—The command format or its associated values were not

valid. Refer to the command description for command usage information.

COMMAND FAILED

—The command was unable to successfully complete. This is

a possible internal software problem.

NOT PROGRAMMED

—Software was unable to program the internal radio

memory or the requested item was not programmed.This is a serious internal

radio error. Contact GE MDS.

TEXT TOO LONG

—Response to

OWN

OWM

command when too many char-

acters are entered. Refer to the command description for command usage

information.

NOT AVAILABLE

—The entered command or parameter was valid, but it referred

to a currently unavailable choice. Refer to the command description for com-

mand usage information.

ACCESS DENIED

—The command is unavailable to the user. Refer to the com-

mand descriptions for command information.

EEPROM FAILURE

— The

INIT

command was unable to write to EEPROM. This

is a serious internal radio error. Contact GE MDS.

See

Table 9

for a summary of the user commands.

Table 9. Command Summary

Command name

Function

ALARM

Details Page 21

Read current operating condition of radio.

AMASK [0000 0000–FFFF

FFFF]

Details Page 21

Set or display hex code identifying which events

trigger an alarm.

ASENSE [HI/LO]

Details

Page 23

Set or display the state of the alarm output signal

to ACTIVE HI or ACTIVE LO.

BAUD [xxxxx abc]

Details

Page 24

Set or display the DATA INTERFACE data rate

and control bits.

BUFF [ON, OFF] [xxx]

Details Page 24

Enables or disables the internal radio data buffer.

CTS [0–255]

Details Page

Set or display the Clear-to-Send delay in seconds.

CKEY [ON–OFF]

Details

Page 25

Enables or disables the continuously keyed

mode. Note: Remotes cannot receive when

keyed.

DATAKEY [ON, OFF]

Details Page 25

Enables or Disables key-on-data mode

(ON = key-on-data or RTS, OFF = key-on-RTS).

DEVICE [DCE, CTS KEY]

Details Page 25

Set/display device mode.

DKEY

Details Page 26

Dekey the radio (transmitter OFF). This is

generally a radio test command.

DIN [ON/OFF]

Details Page

Configures local diagnostic link protocol.

Содержание MDS 9710T

































































Результаты поиска

Содержание MDS 9710T

Отзывы:

Похожие инструкции для MDS 9710T

Бренды по названию

Популярные бренды

GE MDS 9710T, Техническое руководство

Результаты поиска

Содержание MDS 9710T

Отзывы:

Похожие инструкции для MDS 9710T

Бренды по названию

Популярные бренды