GE Mabe GLD8110 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 27

GE Mabe GLD8110 Скачать руководство пользователя страница 13

‐

13

‐

Using the Dishwasher with the Upper
Rack Removed

Middle Spray Arm

1.

Unsnap and remove the end cap on each side

of the rails.

2.

Pull the rack straight out and off the rails.

3.

Replace the end caps.

4.

Push the rails all the way back into

the

dishwasher.

1.

Check holes in spray arm for bits of

china,

seeds, and other foreign matter.

2.

Check spray arms for rotation.

Removal and Replacement

1.

Pull upper rack all the way out.

2.

Remove plastic bottom of middle

spray

arm.

This will allow the middle spray

arm

and bearing to be removed.

Note:

Install middle spray arm with spray jets

facing the upper rack. Place bearing between

spray arm screw and bottom of the middle arm.

5.

Slide the shower nozzle attachment over

the

spout.

6.

The dishwasher is now ready for use.

Note:

Always use the shower nozzle when the

upper rack is removed.

Note:

If the upper rack experiences poor cleaning

problems, ensure the middle spray arm is turning

freely. If not, disassemble the middle spray arm

and

clean the bearing surface, then reassemble.

Unsap

«
...
11
12
13
14
15
...
»

Содержание Mabe GLD8110




























Отзывы:

Нет отзывов