GE Lumination LUR Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 12

GE Lumination LUR Series Скачать руководство пользователя страница 11

11

Variation of the Fixture 2

Variation of the Fixture 3

Install only one end cap in the middle on each side of each light engine (top).

Endcap with sensor

NOTE:

Ensure that connector and wires are located within end cap

after installation. If wires are too long, push extra wire length back into

grommet. Failure to secure connector and wires within end cap may

result in end cap not being mechanically secure.
NOTE:

For control option, the sensor will be attached with the

appropriate wires for the connector in module.

Bracket with bendable tab is meant to replace the plastic end caps.

Brackets are shipped pre-bent. To connect the wires, un-bend the top tab to

connect all necessary wires, then re-bend the top tab to cover the wires.
NOTE:

Ensure that connector and wires are located within the bracket

after installation. If wires are too long, push extra wire length back into

grommet. Failure to secure connector and wires within end cap may

result in end cap not being mechanically secure.

19

20

Pre-bent

top tab

Alignment

tabs

«
...
9
10
11
12
»

Содержание Lumination LUR Series













Отзывы:

Нет отзывов