GE KTR-11 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 24

background image

KTR-11 Face/Badge Reader

Installation Manual

10

Speaker shroud installation

To install the KTR-11 speaker shroud into an existing face/badge reader, do the following:

1. Unlock and open the door of the KTR-11 face/badge reader.

2. Remover the speaker side screw of the existing speaker bracket.

3. Install the new speaker shroud over the existing bracket as shown below.

4. Install the 6-32 x 1/2 in. screw provided and tighten.

Figure 7. A1: Speaker shroud installation on the KTR-11

Place shroud over speaker bracket

Insert new screw

Remove screw

«
...
12
13
14
15
16
...
»

Содержание KTR-11

























Отзывы:

Нет отзывов

Похожие инструкции для KTR-11

Бренд: 3nStar Страницы: 51

Бренд: Yarvik Страницы: 222

Бренд: Symbol Страницы: 2

Бренд: Dynamic Engineering Страницы: 46

Бренд: Symbol Страницы: 129

Бренд: aqprox! Страницы: 39

Бренд: BUNNING Страницы: 138

Бренд: Power Acoustik Страницы: 78

Бренд: Simplex Страницы: 4

Бренд: Paragon id Страницы: 4

Бренд: Pyle Страницы: 14

Бренд: Lynx Studio Technology Страницы: 36

Бренд: Krüger & Matz Страницы: 40

Air Xpert DWL-AG520

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 33

Air Xpert DWL-AG520

Бренд: D-Link Страницы: 53

Бренд: Antique Automobile Radio Страницы: 4

Бренд: Renkforce Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды