GE JT5000SFSS Скачать руководство пользователя страница 2

2 A

  CUTOUT FOR SINGLE OVENS IN WALL CABINET

NOTE:

 If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim 

both sides equally to establish the cutout width.

These ovens 

are not 

approved for 

stackable 

installations.

Cutout – 

observe all 

dimensions and 

requirements.

Cutout – 

observe all 

dimensions and 

requirements.

2” (5.1 cm) Min.

30.5” (77.5 cm)  

30” models

27” (68.58 cm)  

27” models

Center Line

Center Line

Side-by-Side Installations

Install two ovens in separate cutouts.

Dimension Dimension Description 

27” Single Oven 

30” Single Oven 

 A 

Cabinet 

Width

 

27” (68.6 cm) 

30” (76.2 cm)

 B 

Cutout 

Width

 

25” (63.5 cm) min. 

28

1

ø

2

” (72.4 cm) min. 

  

 

25

1

ø

4

” (64.1 cm) max. 

28

5

ø

8

” (72.7 cm) max.

 C 

Cutout 

Height

 27

5

ø

8

” (70.2 cm) min. 

27

1

ø

4

” (69.2 cm) min. 

  

 

28

1

ø

8

” (71.4 cm) max. 

27

5

ø

16

” (69.4 cm) max.

 

Overlap of Oven Over 

 

1” (2.5 cm) 

11

ø

16

” (1.75 cm) 

 

 

Side Edges of Cutout

 E 

Clearance 

to

 

23” (50.8 cm) min. 

23” (53.3 cm) min. 

 

 

Adjacent Corners, 

  

Drawers, 

Walls, 

etc., 

 

 

When Door Is Open

 

Overlap of Oven 

 

1” (2.5 cm) min. 

1” (2.5 cm) min. 

 

 

Top of Cutout 

 

(1

1

ø

4

” (3.2 cm) for PT9050)

 

Overlap of Oven 

 

1” (2.5 cm) min. 

1

1

ø

4

” (3.2 cm) 

 

 

Bottom of Cutout

 

Junction Box Location 

 

8

3

ø

4

” (22.2 cm) max. 

9

1

ø

2

” (24.1 cm) max. 

 

 

  

right side only 

right side only

2 B

  

CUTOUT FOR SINGLE OVENS – UNDER COUNTER

NOTE: 

These ovens are only approved to be installed under the specific models as labeled on the unit. 

Dimension Dimension Description 

27” Single Oven 

30” Single Oven 

 A 

Cabinet 

Width

 

25” (63.5 cm) min. 

28

1

ø

2

” (72.4 cm) min. 

  

 

25

1

ø

4

” (64.1 cm) max. 

28

5

ø

8

” (72.7 cm) max.

 B 

Cutout 

Height

 27

5

ø

8

” (70.2 cm) min. 

27

1

ø

4

” (69.2 cm) min. 

  

 

28

1

ø

8

” (71.4 cm) max. 

27

5

ø

16

” (69.4 cm) max.

 

Unit Overlap Top

 

1” (2.5 cm) 

1” (2.5 cm) 

  

 

 

(1

1

ø

4

” (3.2 cm) for PT9050)

 

Unit Overlap Bottom

 

1” (2.5 cm) 

1

1

ø

4

” (3.2 cm)

 

Unit Overlap Side Edges

 

1” (2.5 cm) 

11

ø

16

” (1.75 cm)

 

Junction Box Location

  

8

3

ø

4

” (22.2 cm) max. 

9

1

ø

2

” (24.1 cm) max. 

 

 

 

right side only 

right side only

Continue to Section 4.

NOTE: 

One cooktop may be centered over either oven in 

the side-by-side installation.

Cutout – observe 

all dimensions and 

requirements.

2” (5.1 cm) Min.

30.5” (77.5 cm) 30” models

27” (68.58 cm) 27” models

Center Line

Center Line

Side-by-Side Installations

Install two ovens in separate cutouts.

Cooktop

Cutout – observe 

all dimensions and 

requirements.

H

B

F

G

C

D

A

E

Junction 

Box 

Location 

(junction 

box may 

be located 

in adjacent 

cabinet)

22” (55.9 

cm) Min. to 

Bottom of 

Junction 

Box

Cutout Depth  

23-1/2”  

(59.7 cm) Min.

Recommended 

Cutout Location 

from Floor  

32-1/2” (82.6 cm)

Opening 

Between Inside 

Walls Must be 

at Least 28-1/2” 

(72.4 cm) Wide

Note: 

Allow 

1/4” (0.64 cm) 
clearances 
from side 
edges of oven 
door.

Содержание JT5000SFSS

















Отзывы: