GE JP989 Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 39

background image

– 23 –

7. Remove (12) 1/4-in. chassis screws (A) that hold the

glass and metal subplate to the cooktop box (3
screws from each side).

8. Raise the front of the glass and metal subplate

assembly slightly and use pliers to bend 2 tabs (B)
approximately 45 degrees outward.

9. Carefully raise the glass and metal subplate assem-

bly from the cooktop box. Do not force it. Wires may
be caught on the flanges of the cooktop box.

10. Insert the 2 tabs (B), on the front of the metal

subplate, into the 2 slots (C) on the top front flange
of the cooktop box.

11. Tilt the glass and metal subplate up and temporarily

install the prop rod near the center as shown.

Note: If you are replacing only 1 defective heater using
Heater Replacement Method 1, skip to that section to
continue. Otherwise, go on to step 12.

12. Remove all 7 knobs from the cooktop.

Note: Remove any knob clips that remain on the control
shafts and reinsert clips inside knob stems.

13. Unplug the 4 connectors below the controls (2 red

and 2 white connectors).

14. Push the heater side of the connectors through the

sidewall slot openings (2 red connectors go to the
right and 2 white connectors to the left).

15. Have a 1/4-in. nut driver ready, then tilt the glass and

metal subplate assembly up to a fully vertical posi-
tion and remove 2 screws from the bottom of the
center control panel plate.

Caution: Save and replace with the exact screws to
prevent glass breakage (#8-18 x 1/4-in.).

16. Return the glass and metal subplate back to the

tilted position supported by the prop rod, then re-
move the top screw from the center control panel
plate.

17. Pull the control panel plate away from the glass until

all 7 shafts pull out of the rubber grommets. Let the
control panel rest on the top of the burner box
chassis.

Note: If you are replacing a broken glass cooktop, skip
to Broken Glass Replacement section.
• If you are replacing a defective heater, skip to the
Heater Replacement Method 2 section.

GEA00234

C

B

A

A

GEA00301

Screws

Side Wall

Side Wall
Slot Opening

Side Wall

Side Wall
Slot Opening

2 White

2 White
Connectors

2 Red
Connectors

Screws

Side Wall
Slot Opening

Side Wall
Slot Opening

2 White
Connectors

2 Red
Connectors

GEA00233

Prop

Rod

Spring Clip and
Coil Spring

«
...
23
24
25
26
27
...
»

Содержание JP989 Series








































Отзывы:

Нет отзывов

Похожие инструкции для JP989 Series

Бренд: K&H Страницы: 13

Бренд: Buffalo Страницы: 8

Бренд: Baumatic Страницы: 44

HC-1006, HC-1256, HC2256

Бренд: Wells Страницы: 12

Бренд: Kruger Страницы: 20

Бренд: Smeg Страницы: 32

Бренд: Jenn-Air Страницы: 16

Бренд: Indesit Страницы: 76

Бренд: Franke Страницы: 44

Бренд: inventum Страницы: 40

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 7

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 1

Бренд: Hotpoint Страницы: 36

Бренд: Hotpoint Страницы: 32

Бренд: Hotpoint Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды