GE Homespring UF 100 Скачать руководство пользователя страница 7

Страница: 7 / 43

System

Cap

Backpulse

Tank

System

Base

Air Blad-

der Valve

Outlet port

Drain port

Inlet port

Air Relief

Valve

System

Casing

Uf 209 model shown.

all other models may be labeled similarly.

fiGUrE 4

UFC 207, UF 207, UFC 209, UF 209, UFC 211, and

UF 211

System (pre-assembled)

System Base

Advanced Plus Controller

Transformer (120VAC)

Carbon Prefilter for UFC 207, UFC 209, UFC 211

Stainless Steel Prefilter for UF 207, UF 209, UF 211

Two Stainless Steel Flex Hoses

Cap Wrench

Inside the bubble bag:

1 – Drain Solenoid Valve (Normally Closed)

1 – Air Relief Valve

1 – Nylon Elbow

3 – 3/8” bolts

2 – ¼” Mini Ball Valves with Plugs

3 – washers

3 – ¼” x 2 ½” anchors

3 – shims

2 – ¾” Inlet/Outlet Fittings

1- ½” Nipple

Surface Water Kit: (Optional)

1 – External Prefilter Housing

Mounting screws

1 – Wall Bracket Kit

1 – Check Valve

1 – ¼” Mini Ball Valve with Plug

4 – ½” Lag Bolts

1– Inlet Solenoid Valve (Normally Open)

1 – External Prefilter

cartridge (30-micron nominal)

•

Indoors with ambient temperature between 40

F-90

C-32

•

Drillable floor, patio stone, or wood base

•

Electrical outlet, 120VAC, within 10’ (305cm)

•

Existing water equipment (e.g. water softeners, filters

upstream and UV downstream)

•

Recommended household water pressure is 30 psi

minimum. If water pressure is less than 30psi, adjust

Backpluse Tank pressure. Refer to Step 4 in the

System installation

section.

•

Drain within 20’ (610cm) and up to 72” (183cm)

high. If the System is to be equipped with an Inlet

Solenoid Valve, the drain cannot be higher than the

drain port of the System for proper draining.

Note: All outlets downstream of the System will provide

filtered water. A dedicated line, diverted from the main

water line, is recommended to be installed upstream of the

System for all exterior taps, pool or hot tub makeup valves,

and irrigation systems. This set-up will help prolong the life

of the System membrane.

Horizontal Mounting Kit: (Optional)

2 – Cast Iron Stands

2 – Cast Iron Cross

Members

1 – Metal Support Strap 1 – Air Relief Valve

1 – Brass ½” Elbow

1 – Brass ¼” Tee

1 – Brass ½” Plug

1 – Foam gasket

1 – PVC ½” Nipple at 2” long

1 – Brass ½” x ¼” Reducer Elbow

1 – Polypropylene ¼” Close Nipple

1 – Polypropylene ½” Close Nipple

1 – Concrete floor bolt

4 – Wall mounting bolts 2½” long

3 – ¼” x 1” bolt & lock nut

5 –

” x 1¼” bolt & lock nut

Horizontal mounting

If this installation requires the System to be installed hori-

zontally, complete the steps described in this section. If the

System is to be installed in a vertical orientation, go to the

System installation

section.

The Horizontal Mounting Kit is purchased separately and can

only be installed with UFC 207, UF 207, UFC 209, UF 209, UFC

211, and UF 211 models. The Horizontal Mounting Kit must

be used in the installation of Horizontally-mounted Systems.

UFC 100, UF 100, and UF 100 with optional Surface

Water Option Kit models cannot be installed horizontally.

Pre-installation inspection

Prior to beginning the installation, check for the following:

•

Space near point of entry of water supply

•

Footprint and Height Clearance:

Vertical Systems

Footprint:

minimum18”x18” (46cm x 46cm)

Height clearance:

UFC 207, UF 207 - minimum 68” (173cm)

All others - minimum 74” (188cm)

Horizontally-mounted Systems

Footprint (including 14” (36cm) of clearance beyond the

System Cap:

UFC 207, UF 207 - minimum 24” x 68” (61cm x 173cm)

All others - minimum 24” x 74” (61cm x 188cm)

Height clearance:

minimum 36” (91cm)

•

All Systems - level area (for floor mounting)

Part identification

Preparing for installation

Содержание Homespring UF 100












































Результаты поиска

Содержание Homespring UF 100

Отзывы:

Бренды по названию

Популярные бренды

GE Homespring UF 100, Руководство по эксплуатации

Результаты поиска

Содержание Homespring UF 100

Отзывы:

Бренды по названию

Популярные бренды