GE GNSF18Z01 Скачать руководство пользователя страница 6

Страница: 6 / 32

Installation instructions.

Typical Installation Illustration

Optional 3-Valve Bypass Installation Illustration

Soft water

Hard water to
outside faucets

MAIN W

ATER PIPE

Hard water

NOTE:

See

Drain Hose

Connections

section.

24V transformer

120-volt outlet

Hard water

Soft water

From softener
outlet

To softener
inlet

Hard water

Soft water

From softener
outlet

To softener
inlet

CROSS-OVER

Use if water supply flows from the left.

Include single or 3-valve bypass.

MAIN W

ATER PIPE

Soft water

Hard water

24V transformer

120-volt outlet

Bypass valve

Hard water to
outside faucets

Inlet valve

Outlet valve

3-valve bypass system

For soft water service:
• Open the inlet and outlet

valves

• Close the bypass valve

For bypass hard water:
• Close the inlet and outlet

valves

• Open the bypass valve

Salt hole
cover
removed

SALT
GOES HERE

Brinewell

INLET

Washer (2)

Copper tube, 3/4

″

(2)

Installation nut (2)

Bypass Valve
• Pull out for service
• Push in for bypass

NOTE:

Threads on the bypass

valve are 1

″

male pipe. If 1

″

pipes are needed, do not use
the copper tubes and nuts
included. Buy 1

″

pipe thread

female adapter, and plumb
directly to 1

″

threads.

Adapters for this installation are not supplied with the softener.

To order these adapters, call GE Parts 800-626-2000. (Ask for Part # WS60X10006.)

Nut (2)

Copper
tube,
3/4

″

(2)

Washer (2)

Installation adapter (2) (see above)

INLET

NOTE:

Threads on the installation adapters are 1

″

male pipe. If 1

″

pipes are needed, do not use the

copper tubes and nuts included. Buy 1

″

pipe thread

female adapter and plumb directly to 1

″

threads on

installation adapters.

CROSS-OVER

Use if water supply flows from

the left. Include single or

3-valve bypass.

Fig. 1

Fig. 2

Union (not supplied) (2)

Содержание GNSF18Z01

































Результаты поиска

Содержание GNSF18Z01

Отзывы:

Бренды по названию

Популярные бренды

GE GNSF18Z01, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание GNSF18Z01

Отзывы:

Бренды по названию

Популярные бренды