![GE GLD2800T Скачать руководство пользователя страница 11](http://html.mh-extra.com/html/ge/gld2800t/gld2800t_owners-manual_125784011.webp)
11
Co
ns
um
er
S
up
po
rt
Tro
ub
les
ho
ot
in
g T
ip
s
O
pe
ra
tin
g I
ns
tru
cti
on
s
Sa
fe
ty
In
str
uc
tio
ns
SPEED CYCLE
7.5 gal., 35–70 min.
(on some models) This cycle is for everyday dishes and glassware.
RINSE ONLY
2.5 gal., 10 min.
For rinsing partial loads that will be washed later. Do not use detergent with this cycle.
nOTE:
This dishwasher is equipped with a cleansensor
™
with automatic temperature control; therefore, cycle
length and time may vary depending on soil and temperature conditions.
nOTE:
only the
SAnI WASH
cycle has been designed to meet the requirements of section 6, nsF 184 for soil
removal and sanitization efficacy.
Options
The light above the selected pad will be
On
to indicate which
EnHAnCEMEnT/ExTrA
has been selected.
STEAM
For use with heavily soiled and/or dried-on, baked-on soils. This option
MuST
be selected
prIOr
(on some models) to starting the cycle.
The
STEAM
option adds 24 minutes to the cycle time.
HEATED DRY
When
HEATEd dry
is off, dishes will air dry.
light oFF
HEATED DRY
Turns the heater on for faster drying. This will extend the total cycle time between
light on
8 and 38 minutes depending on the cycle selected.
nOTE: HEATEd dry
cannot be
selected with
rInSE Only
cycle.
LOCK
You can lock the controls to prevent any selections from being made. or you can lock
the controls after you have started a cycle.
children cannot accidentally start dishwasher by touching pads with this option selected.
To unlock the dishwasher controls
, touch and hold the
HEATEd dry
pad for 3
seconds. The light above the
lOCK
pad will turn off.
To lock the dishwasher control
,
touch and hold the
HEATEd dry
pad for 3 seconds. The light above the
lOCK
pad
will turn on.
ADDED HEAT
When selected, the cycle will run with heating element on longer and may increase
cycle times to improve both wash and dry performance.
nOTE:
Cannot be selected with
rInSE Only
cycle.
DELAY HOURS
You can delay the start of a wash cycle for up to 9 hours. Touch the
dElAy HOurS
pad
to choose the number of hours you want to delay the start of the cycle; then touch
STArT/rESET
. The machine will count down and start automatically at the correct time.
Touching
STArT/rESET
a second time will cancel the
dElAy STArT
selection
.
nOTE:
If you forget to fully close the door, a reminder signal will beep until you do so.
RESET
To change a cycle after washing starts, touch the
STArT/rESET
pad to cancel the
cycle. For some models, the
STArT/rESET
light will flash while the water is pumped
out. This takes approximately 90 seconds. The door must be closed to complete pump
out. When the light stops flashing, the dishwasher can be reprogrammed and
restarted. Buttons will not respond during pump out.
For other models, the
STArT/rESET lEd
will turn off and the drain pump will pump
water out of the dishwasher for 90 seconds and then turn off. Cycle selection and
option
lEd
’s will remain on, and buttons will respond during pump out. If the
STArT/rESET
is pressed while the dishwasher is in pump out, the
STArT/rESET lEd
will turn on and the dishwasher will start a new wash cycle
GEAppliances.com
4
STArT
Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the
STArT/rESET
pad once to begin the cycle. Water begins to fill the dishwasher, and approximately 60
seconds later the wash action begins.
nOTE:
The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the
dishwasher door is fully closed, the control panel lights will display the last settings you selected.
If you don’t want to change any of the settings, simply touch the
STArT/rESET
pad to begin the cycle.
If the door is closed, the indicator lights will turn off if the
STArT/rESET
pad is not selected within two
minutes. To activate the display, open and close the door or press any pad.
Also, if a power failure occurs,
nOrMAl WASH
and
HEATEd dry
will automatically be programmed.
Make any new selections and touch the
STArT/rESET
pad to begin the cycle.
ClEAn
The
ClEAn
light will illuminate and a double beep will sound when a wash cycle is complete. On some
models, the
ClEAn
light will turn off when the door is opened. On other models, the
ClEAn
light will
remain on until the door is opened and then relatched or until any keypad is pressed while the door is
latched shut.
5
6