GE GEWADREW5001 Скачать руководство пользователя страница 1

BEFORE YOU BEGIN

Read these instructions completely and carefully.

 

IMPORTANT

 –

 Save these instructions for local 

electrical inspector’s use.

 

IMPORTANT

 –

 Observe all governing codes and 

ordinances.

 

Install the clothes dryer according to the manufacturer’s 

instructions and local codes.

 

Note to Installer –

 Be sure to leave these instructions 

with the Consumer.

 

Note to Consumer –

 Keep these instructions for future 

reference.

 

Clothes dryer installation must be performed by a 

qualified installer.

 

This dryer 

must

 be exhausted to the outdoors. 

 

Before the old dryer is removed from service or 

discarded, remove the dryer door.

 

Service information and the wiring diagram are located 

in the control console.

 

Do not allow children on or in the appliance. Close 

supervision of children is necessary when the appliance 

is used near children.

 

Proper installation is the responsibility of the installer. 

 

Product failure due to improper installation is not 

covered under the Warranty

.

 

Install the dryer where the temperature is above 50°F 

for satisfactory operation of the dryer control system.

•  Remove and discard existing plastic or metal foil duct 

and replace with UL-listed duct.

Questions? Call 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com

- Fire Hazard

WARNING

 

Clothes dryer installation must be performed by a 

qualified installer.

 

Install the clothes dryer according to these 

instructions and local codes.

 

DO NOT

 install a clothes dryer with flexible plastic 

venting materials. If flexible metal (semi-rigid or 

foil-type) duct is installed, it must be UL-listed and 

installed in accordance with the instructions found 

in “Connecting the Dryer to House Vent” later in 

this manual. Flexible vent materials are known to 

collapse, be easily crushed and trap lint. These 

conditions will obstruct dryer airflow and increase 

the risk of fire.

 

DO NOT

 install or store this appliance in any 

location where it could be exposed to water or 

weather.

 

To reduce the risk of severe injury or death, follow 

all installation instructions.

 

Save these instructions. (Installers: Be sure to leave 

these instructions with the customer.)

Installation            Electric Dryers 

Instructions 

       

     

01

  

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill you or hurt you and others. 

All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These 

words are defined as:

   

Indicates a hazardous situation which, if not avoided, 

will

 result in death or serious injury.

   

Indicates a hazardous situation which, if not avoided, 

could 

result in death or serious injury.

   

Indicates a hazardous situation which, if not avoided, 

could 

result in minor or moderate injury.

DANGER
WARNING
CAUTION

31-16755

 

   

01-15

 

GE

234D2318P001

Printed in Mexico

Содержание GEWADREW5001

















Отзывы: