background image

Consumer Support

Troubleshooting T

ips

Operating Instructions

Safety Instructions

Installation Instructions

Normal operating sounds.

Before you call for service…

Troubleshooting Tips 
Save time and money! Review the charts on the following
pages first and you may not need to call for service.

Newer refrigerators sound different from older refrigerators. 
Modern refrigerators have more features and use newer technology.

HUMMM...

WHOOSH...

The new high efficiency compressor may run faster and longer
than your old refrigerator and you may hear a high-pitched
hum or pulsating sound while it is operating.

You may hear a whooshing sound when the doors close. This is
due to pressure equalizing within the refrigerator.

You may hear the fans spinning at high speeds. This happens
when the refrigerator is first plugged in, when the doors are
opened frequently or when a large amount of food is added to
the refrigerator or freezer compartments. The fans are helping
to maintain the correct temperatures.

The fans change speeds in order to provide optimal cooling
and energy savings.

CLICKS, POPS,

CRACKS and SNAPS

You may hear cracking or popping sounds when the
refrigerator is first plugged in. This happens as the refrigerator
cools to the correct temperature.

The freezer control will click when starting or stopping the
compressor.

Defrost timer snapping in and out of the defrost cycle.

Expansion and contraction of cooling coils during and after
defrost can cause a cracking or popping sound.

On models with an icemaker, after an icemaking cycle, you
may hear the ice cubes dropping into the ice bucket.

On models with a dispenser, during water dispense, you 
may hear the water lines move at initial dispense and after
dispenser button is released. 

WATER SOUNDS

The flow of refrigerant through the freezer cooling coils may
make a gurgling noise like boiling water.

Water dropping on the defrost heater can cause a sizzling,
popping or buzzing sound during the defrost cycle.

A water dripping noise may occur during the defrost cycle as
ice melts from the evaporator and flows into the drain pan.

Closing the door may cause a gurgling sound due to pressure
equalization.

Do you hear what I hear? These sounds are normal.

Problem

Possible Causes

What To Do

Refrigerator does not

Refrigerator in defrost cycle.

Wait about 30 minutes for defrost cycle to end. 

operate

Control in 

0 (off) 

position.

Move the control to a temperature setting.

Refrigerator is unplugged.

Push the plug completely into the outlet.

The fuse is blown/circuit 

Replace fuse or reset the breaker.

breaker is tripped.

Vibration or rattling

Leveling legs need adjusting.

See

Level the Refrigerator.

(slight vibration 
is normal)

For additional information on normal
icemaker operating sounds, see the 

About the automatic icemaker

section.

34

Product Code: GEPDS20MFSWW

www.spaequip.com

P: 707-737-1100 F: 707-737-1150

Page 21 of 21

Содержание GEPDS20MFSWW






















Отзывы: