DET-653C
EntelliGuard
®
G Circuit Breaker Application Guide
24-May-12
Section 4. Accessories
©2012 General Electric All Rights Reserved
41
Table 4.2. Closing Coil Characteristics
Type
Power
Consumption
Nominal Control
Voltage
Catalog
Number
Closing
Coil
DC: 350W,
20 W (sealed)
AC: 350W
(inrush),
20W (sealed)
24Vdc
GCCN024DR
48Vac/dc
GCCN048R
60 to 72Vdc
GCCN060DR
110/130/120Vac
GCCN120R
208Vac
GCCN208AR
220Vdc/240Vac
GCCN240R
250Vdc/277Vac
GCCN277R
Command
Operated
Closing
Coil
DC: 350W,
20W (sealed)
AC: 350W
(inrush),
20W (sealed)
24Vdc
GCCC024DR
48Vac/dc
GCCC048R
60 to 72Vdc
GCCC060DR
110/130/120Vac
GCCC120R
208Vac
GCCC208AR
•
Duty cycle = 2/min.
•
Closing coil inrush = 350VA.
Command Operation Module
This module energizes the closing coil to cause the breaker
to close whenever control power is applied to the accessory
and when commanded from the breaker trip unit or breaker
front panel push button (electrical closing.)
Shunt Trip
Energizing the shunt trip (ST), via local or remote input, will
instantaneously activate the circuit breaker mechanism,
ensuring a rapid open operation. The shunt trip is
continuously rated and does not require an auxiliary switch
in series with the coil. The shunt trip is a straightforward,
field installable accessory available in wide range of
voltages. See Table 4.3.
Table 4.3. Extended Range Shunt Trip for UL Ground Fault
and ANSI DC Rating Applications.
Nominal Control Voltage
Catalog Number
24Vdc
GSTG024DR
48Vac/dc
GSTG048R
70/72Vdc
GSTG072DR
110Vdc/120 Vac
GSTG120R
125 Vdc
GSTG125DR
208 Vac
GSTG208AR
240 Vac
GSTG240R
250 Vdc/277 Vac
GSTG250R
•
Pickup range = 55%-110%.
•
Duty cycle = 2/min.
•
Inrush = 480A (ac), 480W (dc).
•
Holding = 60VA (ac), 50W (dc).
Status Indication Switch (Coil Signaling Contact)
A plug-in module is available to provide status indication via
the secondary disconnects and trip unit. Coil Signaling
Contacts are available for closing coils, shunt trips and under
voltage releases (Table 4.4). Contact is mounted on top of the
Accessory Device. One of the low signal (Hi-Fi) contacts is
always wired to the tip Unit.
Table 4.4. Coil Signaling Contact Module
Type and
Configuration
Rating
Cat. No.
1 Power rated +
1 Low signal (Hi-Fi)
(1NO contact each)
AC
120Vac
6A
GCSP1R
250Vac
6A
DC
125Vac
0.5A
250Vdc
0.25A
AC
125Vac
0.1A
DC
30Vdc
0.1A
2 Low signal (Hi-Fi)
(1NO contact each)
AC
125Vac
0.1A
GCSP2R
Under Voltage Release (UVR) with Fixed Time Delay
The UVR instantaneously activates the circuit breaker trip
mechanism when the source voltage drops below the low
voltage threshold. The UVR is also a simple, field installable
device. NOTE: This accessory acts as a permissive; it is a no-
voltage/no-close device. The circuit breaker cannot be
closed (manually or electrically) unless the undervoltage
release coil is energized above the required threshold. The
undervoltage release with fixed time delay is specifically
intended for applications where a delay period (ride-through)
is required due to potential voltage events. The delays are
50msec when system voltage drops to 50% and 20msec
when system voltage drops below 50% (Table 4.5).
Table 4.5. UVR Operating Characteristics
Power
Consumption
Nominal Control
Voltage
Catalog
Number
DC: 350W,
2 W (sealed)
AC: 350W
(inrush),
20W (sealed)
24 Vdc
GUVT024DR
24/30Vdc
GUVT030DR
40Vdc; 48Vac/dc
GUVT048R
60Vdc
GUVTO60DR
110 Vdc/130 Vdc;
120 Vac
GUVT120R
208Vac
GUVT208AR
220Vdc/240Vac
GUVT240R
250Vdc/277Vac
GUVT277R
•
Duty cycle = 2/min.
•
Inrush = 350VA (ac), 350W (dc).
•
Holding = 60VA (ac), 50W (dc).
